The reason why the contacts often connected in series when controlling small DC motors.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 33, Problem 1RQ

To determine

The reason why the contacts often connected in series when controlling small DC motors.

Expert Solution & Answer

Explanation of Solution

To break the motor circuit or to stop the motor the arc formation may occur.

In that case only load contact is required to break the circuit and to stop the motor but in that case current does not fall to zero as like the alternating current. This shows that the arc interruption in case of the DC motor is difficult.

In case the direct current do not fall the zero periodically so the severity of the arc and the risk to the damage is high.

To aid the arc interruption the load contacts in the small DC motor is connected in the series connection. Also, it increases the total air gap between the contacts and in arc quenching.

Thus, the contacts are in series in controlling small DC motor to aid the arc interruption.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

1. A 40 lb. force is applied at point E. There are pins at A, B, C, D, and F and a roller at A. a. Draw a FBD of member EFC showing all the known and unknown forces acting on it. b. Draw a FBD of member ABF showing all the known and unknown forces acting on it. c. Draw a FBD of member BCD showing all the known and unknown forces acting on it. d. Draw a FBD of the entire assembly ADE showing all the known and unknown forces acting on it. e. Determine the reactions at A and D. f. Determine the magnitude of the pin reaction at C. 40 lbs. B A 6 in. 4 in. D F -5 in.4 in 4.

A crude oil of specific gravity0.85 flows upward at a volumetric rate of flow of 70litres per second through a vertical venturimeter,with an inlet diameter of 250 mm and a throat diameter of 150mm. The coefficient of discharge of venturimeter is 0.96. The vertical differences betwecen the pressure toppings is 350mm. i) Draw a well labeled diagram to represent the above in formation i) If the two pressure gauges are connected at the tapings such that they are positioned at the levels of their corresponding tapping points, determine the difference of readings in N/CM² of the two pressure gauges ii) If a mercury differential manometer is connected in place of pressure gauges, to the tappings such that the connecting tube up to mercury are filled with oil determine the difference in the level of mercury column.

Can you solve it analytically using laplace transforms and with Matlab code as well please. Thank You

Answer 2

Question

Chapter 33, Problem 1RQ

To determine

The reason why the contacts often connected in series when controlling small DC motors.

Expert Solution & Answer

Explanation of Solution

To break the motor circuit or to stop the motor the arc formation may occur.

In that case only load contact is required to break the circuit and to stop the motor but in that case current does not fall to zero as like the alternating current. This shows that the arc interruption in case of the DC motor is difficult.

In case the direct current do not fall the zero periodically so the severity of the arc and the risk to the damage is high.

To aid the arc interruption the load contacts in the small DC motor is connected in the series connection. Also, it increases the total air gap between the contacts and in arc quenching.

Thus, the contacts are in series in controlling small DC motor to aid the arc interruption.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 33, Problem 1RQ

To determine

The reason why the contacts often connected in series when controlling small DC motors.

Expert Solution & Answer

Explanation of Solution

To break the motor circuit or to stop the motor the arc formation may occur.

In that case only load contact is required to break the circuit and to stop the motor but in that case current does not fall to zero as like the alternating current. This shows that the arc interruption in case of the DC motor is difficult.

In case the direct current do not fall the zero periodically so the severity of the arc and the risk to the damage is high.

To aid the arc interruption the load contacts in the small DC motor is connected in the series connection. Also, it increases the total air gap between the contacts and in arc quenching.

Thus, the contacts are in series in controlling small DC motor to aid the arc interruption.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 33, Problem 1RQ

To determine

The reason why the contacts often connected in series when controlling small DC motors.

Expert Solution & Answer

Explanation of Solution

To break the motor circuit or to stop the motor the arc formation may occur.

In that case only load contact is required to break the circuit and to stop the motor but in that case current does not fall to zero as like the alternating current. This shows that the arc interruption in case of the DC motor is difficult.

In case the direct current do not fall the zero periodically so the severity of the arc and the risk to the damage is high.

To aid the arc interruption the load contacts in the small DC motor is connected in the series connection. Also, it increases the total air gap between the contacts and in arc quenching.

Thus, the contacts are in series in controlling small DC motor to aid the arc interruption.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 33, Problem 1RQ

To determine

The reason why the contacts often connected in series when controlling small DC motors.

Expert Solution & Answer

Explanation of Solution

To break the motor circuit or to stop the motor the arc formation may occur.

In that case only load contact is required to break the circuit and to stop the motor but in that case current does not fall to zero as like the alternating current. This shows that the arc interruption in case of the DC motor is difficult.

In case the direct current do not fall the zero periodically so the severity of the arc and the risk to the damage is high.

To aid the arc interruption the load contacts in the small DC motor is connected in the series connection. Also, it increases the total air gap between the contacts and in arc quenching.

Thus, the contacts are in series in controlling small DC motor to aid the arc interruption.

Answer 6

Chapter 33, Problem 1RQ

To determine

The reason why the contacts often connected in series when controlling small DC motors.

Expert Solution & Answer

Explanation of Solution

To break the motor circuit or to stop the motor the arc formation may occur.

In that case only load contact is required to break the circuit and to stop the motor but in that case current does not fall to zero as like the alternating current. This shows that the arc interruption in case of the DC motor is difficult.

In case the direct current do not fall the zero periodically so the severity of the arc and the risk to the damage is high.

To aid the arc interruption the load contacts in the small DC motor is connected in the series connection. Also, it increases the total air gap between the contacts and in arc quenching.

Thus, the contacts are in series in controlling small DC motor to aid the arc interruption.

Answer 7

Chapter 33, Problem 1RQ

To determine

The reason why the contacts often connected in series when controlling small DC motors.

Answer 8

Expert Solution & Answer

Explanation of Solution

To break the motor circuit or to stop the motor the arc formation may occur.

In that case only load contact is required to break the circuit and to stop the motor but in that case current does not fall to zero as like the alternating current. This shows that the arc interruption in case of the DC motor is difficult.

In case the direct current do not fall the zero periodically so the severity of the arc and the risk to the damage is high.

To aid the arc interruption the load contacts in the small DC motor is connected in the series connection. Also, it increases the total air gap between the contacts and in arc quenching.

Thus, the contacts are in series in controlling small DC motor to aid the arc interruption.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

Ch. 33 - Prob. 1RQ Ch. 33 - Why is direct current more difficult to interrupt...Ch. 33 - Why are clapper-type contactors generally used to...Ch. 33 - Prob. 4RQ Ch. 33 - How is the inrush current to large DC motors often...Ch. 33 - Prob. 6RQ Ch. 33 - How is the FCR connected in relationship to the...Ch. 33 - Prob. 8RQ Ch. 33 - Prob. 9RQ

The reason why the contacts often connected in series when controlling small DC motors.

Concept explainers

The reason why the contacts often connected in series when controlling small DC motors.

Explanation of Solution

Want to see more full solutions like this?

Chapter 33 Solutions