Motor C |d L1- L2- PROBLEMS 3.7-11 and 3.7-12

Q: The nature of the stresses

A: Given; A helical gear with pressure angle,α= 200 and β=300 helix angleAt the  mid span of a shaft is…

Q: ide information about tempering heat treatment temperature stages, microstructures formed and their…

A: Tempering is a heat treatment process, which is mostly used to increase the ductility, toughness and…

Q: 4 mm module 20° full-depth The gear shown above is to transmit 1 kW at a speed of 200 rev/min. Find…

A:

Q: A motor drives a shaft at 300 rpm and a power output of 100 kW. The shaft is made of A-36 steel and…

A:

Q: A gear train is composed of four helical gears with the three shaft axes in a single plane, as shown…

A:

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: In the gear system shown in the figure, the motor applies a torque of 231 N-m to the gear at A. A…

A: The given information in the problem is listed in the following attached image:

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

A:

Q: Circular solid ACB shaft is fixed supported between the wall at A and B. If the allowable shear…

A: Allowable shear stress τallowable=42 MPa=42×106 N/m2Let the maximum torque applied at section C be…

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

A:

Q: Two shafts are connected by gears. The diameter of the two shafts is 1.5 in. They have the same…

A: Given: Diameter of two shafts (D)=1.5in  or 0.125ftShear modulus G=11.2×106Radius of gear E=4in or…

Q: he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if…

A: ⇒given data;⇒shear modulus(G)=75GPa                          =75*103MPa⇒angle of twist for gear…

Q: the centre distance in mm

A: Given data;  Compound gear train with gears;  p=20 teeth  Q= 40 teeth  R= 15 teeth  S=20 TeethGears…

Q: Two motors deliver 119 hp each at 1000 rpm to shafts at A and D. The shaft transmits torque through…

A: Data given-  Motor deliver = 119 hp  N = 1000 rpm  Shear modulus = 11 × 103 ksi

Q: The four rigid gears, loaded as shown in the figure, are attached to a 1.63-in.-diameter steel…

A: The shear stress in the shaft AB can be determined as shown below.

Q: PROBLEM 2. The turbine in the figure generates 90 kW power. 50 kW of power is drawn from the gear at…

A: Total Power P = 90kW  Power with gear C Pc = 50kW = 50×103 W Power with gear D PD = 40kW = 40×103 W…

Q: A shaft supported at the ends carries a spur gear and is to transmit 10 kW at 200 rpm. The weight of…

A: Consider a shaft of diameter d and length L is subjected to a torque T. Then, torsional shear stress…

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supplies by motor is The speed of motor is The diameter of shaft 1 and 2 is The modulus of…

Q: A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The…

A:

Q: Bearing stress 5. Please provide proper discussion and illustration also complete solution and…

A: given; transmitting force(F)=50KN                                     =50*103Nshear stress on…

Q: left and right bearings. The C is 600 mm and that of gea e between the centre line of . The shaft…

A:

Q: Figure 2 shows a solid shaft consisting of two prismatic circular parts in equilibrium under the…

A:

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supply by the motor is The speed of the motor is The diameter of shafts 1 and 2 is The…

Q: For the gear system shown in the figure, the diameter of shaft AB=12 mm. Determine the diameter of…

A:

Q: The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof…

A: Given: The power, P = 300 kW The speed of shaft, N = 32 Hz The power at gear B, P1 = 120 kW The…

Q: An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress…

A: Given Data Diameter of bar AB is : d1=90 mm Diameter of bar BC is : d2=60 mm Allowable stress is :…

Q: A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1.…

A:

Q: Using G =83 GPa, determine the maximum shearing stres

A:

Q: angle angle and 3 1 ween two bearin

A:

Q: The solid 25 mm diameter shaft is used to transmit torques applied to the gears. Use G= 80 GPa.…

A: Given: The diameter of shaft, d = 25 mm = 0.025 m The modulus of elasticity, G = 80 GPa

Q: -1-60 in. and L2= ne the maximum shear stresses T₁, ne the rotation angle DA of gear i in.,…

A: The power supply by the motor is The speed of the motor is The diameter of shafts 1 and 2 is The…

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.