Process Dynamics and Control, 4e
Process Dynamics and Control, 4e
4th Edition
ISBN: 9781119285915
Author: Seborg
Publisher: WILEY
Question
Book Icon
Chapter 3, Problem 3.13E
Interpretation Introduction

(a)

Interpretation:

The response of the given system is to be estimated to be oscillatory or not for an arbitrary change in u.

Concept introduction:

For a function f(t), the Laplace transform is given by,

F(s)=L[f(t)]=0f(f)estdt   ....... (1)

Here, F(s) represents the Laplace transform, s is a variable that is complex and independent, f(t) is any function of time which is being transformed, and L is the operator which is defined by an integral.

f(t) is calculated by taking inverse Laplace transform of the function F(s).

PFE is the partial fraction expansion is the method of expanding the denominator of a fraction into simpler terms.

Laplace transform of higher-order derivatives is given by:

L(dnfdtn)=snF(s)sn1f(0)sn2f(1)(0)sf(n2)(0)f(n1)(0)   ....... (2)

For the general form of the transfer function;

Y(s)X(s)=1τ2s2+2τζs+1

The response of the transfer will be underdamped or oscillatory if ζ<1, critically damped if ζ=1, and overdamped or nonoscillatory if ζ>1.

Interpretation Introduction

(b)

Interpretation:

The steady-state value of yis to be calculated when

u(t2)=1.

Concept introduction:

The value of Kp, steady-state value is calculated by s=0 in the transfer function for the unit step disturbance, that is,

lims0[sY(s)]=Kp

Interpretation Introduction

(c)

Interpretation:

The value of y(t) for a step-change in u is to be calculated.

Concept introduction:

For a function f(t), the Laplace transform is given by,

F(s)=L[f(t)]=0f(f)estdt   ....... (1)

Here, F(s) represents the Laplace transform, s is a variable that is complex and independent, f(t) is any function of time which is being transformed, and L is the operator which is defined by an integral.

f(t) is calculated by taking inverse Laplace transform of the function F(s).

PFE is the partial fraction expansion is the method of expanding the denominator of a fraction into simpler terms.

Laplace transform of higher-order derivatives is given by:

L(dnfdtn)=snF(s)sn1f(0)sn2f(1)(0)sf(n2)(0)f(n1)(0)   ....... (2)

Blurred answer
Students have asked these similar questions
2:41 2) If the number-average degree of polymerization for styrene obtained by the bulk polymerization at 25°C is 5,000, what would be the number-average degree of polymerization if conducted in a 10% solution in toluene (900g of toluene per 100 g of styrene) under otherwise identical conditions? State any assumptions that are needed. (see Table 2-4). Table 2-4 Representative Values of Chain-Transfer Constants Monomer Styrene Chain-Transfer Agent T (°C) C x 104 Styrene 25 bas 0.279 * 50 0.35-0.78 Polystyrene 50 1.9-16.6 Benzoyl peroxide 50 0.13 Toluene 60 0.125 Methyl methacrylate Methyl methacrylate 30 0.117 70 0.2 Poly(methyl methacrylate) 50 0.22-1000 Benzoyl peroxide 50 0.01 Toluene 40 0.170 3) 2 3) Methyl methacrylate is copolymerized with 2-methylbenzyl methacrylate (M₁) in 1,4- dioxane at 60°C using AIBN as the free-radical initiator. (a) Draw the repeating unit of poly(2-methylbenzyl methacrylate). (b) From the data given in the table below, estimate the reactivity ratios of…
A piston–cylinder device initially contains 0.6 m3 of saturated water vapor at 250 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such  that a pressure of 300 kPa is required to move it. Heat is now slowly transferred to the steam until the volume becomes 1 m3. Use the data from the steam tables. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.   Determine the final temperature.   The final temperature is  ºC. Determine the work done during this process Determine the total heat transfer
Consider a mixture of carbon monoxide and water at 25°C:a. Does an azeotrope exist for this mixture at 25°C? If so, at what composition andpressure? If not, how do you know?b. If the total composition of the mixture is 10. mol% carbon monoxide, what will bethe pressure limits of VLE for this mixture at 25°C?   show all the calculation steps
Knowledge Booster
Background pattern image
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Introduction to Chemical Engineering Thermodynami...
Chemical Engineering
ISBN:9781259696527
Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Publisher:McGraw-Hill Education
Text book image
Elementary Principles of Chemical Processes, Bind...
Chemical Engineering
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY
Text book image
Elements of Chemical Reaction Engineering (5th Ed...
Chemical Engineering
ISBN:9780133887518
Author:H. Scott Fogler
Publisher:Prentice Hall
Text book image
Process Dynamics and Control, 4e
Chemical Engineering
ISBN:9781119285915
Author:Seborg
Publisher:WILEY
Text book image
Industrial Plastics: Theory and Applications
Chemical Engineering
ISBN:9781285061238
Author:Lokensgard, Erik
Publisher:Delmar Cengage Learning
Text book image
Unit Operations of Chemical Engineering
Chemical Engineering
ISBN:9780072848236
Author:Warren McCabe, Julian C. Smith, Peter Harriott
Publisher:McGraw-Hill Companies, The