Automotive Technology: A Systems Approach - With Manual and Access
6th Edition
ISBN: 9781305513235
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 27, Problem 12RQ
What is the typical procedure for checking the resistance of the primary winding in an ignition coil?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What happens when the low-voltage current flow in the coil primary winding is interrupted by the switching device?
The primary winding delivers a high-voltage spark to the plugs.
The magnetic field in the coil primary builds.
The secondary voltage drops to zero volts.
High voltage is induced in the secondary windin
The following statement is made about an ignition system: tech a says that the greater the speed of the magnets rotating past a the ignition coil, the greater the voltage will be induced into the ignition coil. Tech b says that the primary windings produce a higher voltage than the secondary winding. Who is correct?
How spark advance mechanisms works in mechanical ignition system and what are its shortcomings?
Chapter 27 Solutions
Automotive Technology: A Systems Approach - With Manual and Access
Ch. 27 - Name the three types of stress testing used to...Ch. 27 - Prob. 2RQCh. 27 - Name the three types of trace pattern display...Ch. 27 - Prob. 4RQCh. 27 - List at least two methods of checking the...Ch. 27 - What happens if one of the ground electrodes of a...Ch. 27 - True or False? The first test when checking a...Ch. 27 - Richer air-fuel mixtures. a. decrease the...Ch. 27 - Prob. 9RQCh. 27 - What does a slope in the spark line represent?
Ch. 27 - True or False? On some engines, if the gap between...Ch. 27 - What is the typical procedure for checking the...Ch. 27 - While checking a pickup coil with an ohmmeter, a...Ch. 27 - A CKP sensor can be checked with all of the...Ch. 27 - Which of the following will cause one or more, but...Ch. 27 - Prob. 1ASRQCh. 27 - Prob. 2ASRQCh. 27 - Prob. 3ASRQCh. 27 - Technician A says that EMI can affect sensor...Ch. 27 - While discussing waste spark EI systems:...Ch. 27 - While discussing how to test a Hall-effect...Ch. 27 - While discussing the possible causes for a...Ch. 27 - Prob. 8ASRQCh. 27 - While discussing EI service and diagnosis:...Ch. 27 - While discussing engine misfire diagnosis:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is the typical output voltage of the ignition transformer? A. 24 V B. 200,000 V C. 115 v D. 10,000 Varrow_forwardIs the resistance in the start winding greater or less than the resistance in the run winding?arrow_forwardWhen energizing or de-energizing a combination starter what safety precaution should always be taken?arrow_forward
- What are the three types of armature windings?arrow_forwardThe load on the outdoor coil influenced by? -The location of the indoor coil -The outdoor temperature and the evaporator heat load -the voltage supplied to the unit -all the above factorsarrow_forwardIn El systems using one ignition coil for every two cylinders: Technician A says that two plugs fire at the same time with the same voltage used by each spark plug. Technician B says that one plug fires in the normal direction (center to side electrode) and the other in reversed polarity (side to center). Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Refer to Figure 211 to answer the following questions. How much voltage will be applied to coil 1CR when it is energized?arrow_forwardWhat are the advantages of alternators over generators?arrow_forwardConsider the following statements relevant to the ignition system of SI engine: 1. Too small a dwell angle will lead to the burning of condenser and contact points. 2. Too small a dwell angle will result in misfiring. 3. Too large a dwell angle will result in burning of condenser and contact points. 4. Too large a dwell will result in misfiring. Which of these statements are correct? (a) 1 and 2 (c) 3 and 4 (b) 2 and 3 (d) 4 and 1arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License