The advantage of the point to point method of connecting the circuit components.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 26, Problem 1RQ

To determine

The advantage of the point to point method of connecting the circuit components.

Expert Solution & Answer

Explanation of Solution

The point to point method is the method which is used to install the circuit components in the control circuit. The wire numbers are given in this method to the wires of the control circuit but not the load circuit. Where all the components are located in the motor circuit and are represented by the dashed lines.

The advantages of the point to point method is that this method is used to show the actual position of the wire of the component that reduces the wastage of the wire.

The component that are insider the control circuit and the outside the circuit can easily be distinguished.

Also, the point to point method show the designation of the wires and the tags.

In this method the troubleshooting and the servicing is easy as the wire numbers are given to the wire, also the components are easy to be identified as the wires are tagged and labelled.

Thus, the advantage of the point to point method is described.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

A hot surface at 150°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m-K) to it, with a center- to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m²K. Determine the rate of heat transfer from the surface for a 1-m × 1-m section of the plate. Also determine the overall effectiveness of the fins. 0.6 cm 0.25 cm The total rate of heat transfer is kW. The fin effectiveness is

Consider a stainless steel spoon (k = 8.7 Btu/h·ft·°F) partially immersed in boiling water at 200°F in a kitchen at 75°F. The handle of the spoon has a cross section of 0.08 in × 0.5 in and extends 7 in in the air from the free surface of the water. The heat transfer coefficient at the exposed surfaces of the spoon handle is 3 Btu/h·ft2·°F. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A spoon is placed inside the container, such that the distance of the water level from the top end of the handle of the spoon is 7 meters. T sub air is indicated in the region outside the container. Identify the assumptions required to solve the problem. Check All That Apply One-dimensional heat transfer analysis is used to solve the problem. One-dimensional heat transfer analysis is used to solve the problem. Bi-dimensional heat transfer analysis is used to solve the problem. Bi-dimensional heat transfer analysis is…

A turbine blade made of a metal alloy (k=17 W/m-K) has a length of 5.3 cm, a perimeter of 11 cm, and a cross-sectional area of 5.13 cm². The turbine blade is exposed to hot gas from the combustion chamber at 1133°C with a convection heat transfer coefficient of 538 W/m²K. The base of the turbine blade maintains a constant temperature of 450°C and the tip is adiabatic. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Hot gas h=538 W/m²K -Turbine blade k = 17 W/m-K p=11 cm, L=5.3 cm A = 5.13 cm² -T=450°C Determine the heat transfer rate to the turbine blade. W. The heat transfer rate is

Answer 2

Question

Chapter 26, Problem 1RQ

To determine

The advantage of the point to point method of connecting the circuit components.

Expert Solution & Answer

Explanation of Solution

The point to point method is the method which is used to install the circuit components in the control circuit. The wire numbers are given in this method to the wires of the control circuit but not the load circuit. Where all the components are located in the motor circuit and are represented by the dashed lines.

The advantages of the point to point method is that this method is used to show the actual position of the wire of the component that reduces the wastage of the wire.

The component that are insider the control circuit and the outside the circuit can easily be distinguished.

Also, the point to point method show the designation of the wires and the tags.

In this method the troubleshooting and the servicing is easy as the wire numbers are given to the wire, also the components are easy to be identified as the wires are tagged and labelled.

Thus, the advantage of the point to point method is described.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 26, Problem 1RQ

To determine

The advantage of the point to point method of connecting the circuit components.

Expert Solution & Answer

Explanation of Solution

The point to point method is the method which is used to install the circuit components in the control circuit. The wire numbers are given in this method to the wires of the control circuit but not the load circuit. Where all the components are located in the motor circuit and are represented by the dashed lines.

The advantages of the point to point method is that this method is used to show the actual position of the wire of the component that reduces the wastage of the wire.

The component that are insider the control circuit and the outside the circuit can easily be distinguished.

Also, the point to point method show the designation of the wires and the tags.

In this method the troubleshooting and the servicing is easy as the wire numbers are given to the wire, also the components are easy to be identified as the wires are tagged and labelled.

Thus, the advantage of the point to point method is described.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 26, Problem 1RQ

To determine

The advantage of the point to point method of connecting the circuit components.

Expert Solution & Answer

Explanation of Solution

The point to point method is the method which is used to install the circuit components in the control circuit. The wire numbers are given in this method to the wires of the control circuit but not the load circuit. Where all the components are located in the motor circuit and are represented by the dashed lines.

The advantages of the point to point method is that this method is used to show the actual position of the wire of the component that reduces the wastage of the wire.

The component that are insider the control circuit and the outside the circuit can easily be distinguished.

Also, the point to point method show the designation of the wires and the tags.

In this method the troubleshooting and the servicing is easy as the wire numbers are given to the wire, also the components are easy to be identified as the wires are tagged and labelled.

Thus, the advantage of the point to point method is described.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 26, Problem 1RQ

To determine

The advantage of the point to point method of connecting the circuit components.

Expert Solution & Answer

Explanation of Solution

The point to point method is the method which is used to install the circuit components in the control circuit. The wire numbers are given in this method to the wires of the control circuit but not the load circuit. Where all the components are located in the motor circuit and are represented by the dashed lines.

The advantages of the point to point method is that this method is used to show the actual position of the wire of the component that reduces the wastage of the wire.

The component that are insider the control circuit and the outside the circuit can easily be distinguished.

Also, the point to point method show the designation of the wires and the tags.

In this method the troubleshooting and the servicing is easy as the wire numbers are given to the wire, also the components are easy to be identified as the wires are tagged and labelled.

Thus, the advantage of the point to point method is described.

Answer 6

Chapter 26, Problem 1RQ

To determine

The advantage of the point to point method of connecting the circuit components.

Expert Solution & Answer

Explanation of Solution

The point to point method is the method which is used to install the circuit components in the control circuit. The wire numbers are given in this method to the wires of the control circuit but not the load circuit. Where all the components are located in the motor circuit and are represented by the dashed lines.

The advantages of the point to point method is that this method is used to show the actual position of the wire of the component that reduces the wastage of the wire.

The component that are insider the control circuit and the outside the circuit can easily be distinguished.

Also, the point to point method show the designation of the wires and the tags.

In this method the troubleshooting and the servicing is easy as the wire numbers are given to the wire, also the components are easy to be identified as the wires are tagged and labelled.

Thus, the advantage of the point to point method is described.

Answer 7

Chapter 26, Problem 1RQ

To determine

The advantage of the point to point method of connecting the circuit components.

Answer 8

Expert Solution & Answer

Explanation of Solution

The point to point method is the method which is used to install the circuit components in the control circuit. The wire numbers are given in this method to the wires of the control circuit but not the load circuit. Where all the components are located in the motor circuit and are represented by the dashed lines.

The advantages of the point to point method is that this method is used to show the actual position of the wire of the component that reduces the wastage of the wire.

The component that are insider the control circuit and the outside the circuit can easily be distinguished.

Also, the point to point method show the designation of the wires and the tags.

In this method the troubleshooting and the servicing is easy as the wire numbers are given to the wire, also the components are easy to be identified as the wires are tagged and labelled.

Thus, the advantage of the point to point method is described.