The parameter which sets the limit of d .

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 24, Problem 1DQ

To determine

The parameter which sets the limit of d.

Expert Solution & Answer

Explanation of Solution

When the distance existing between plates increases, the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Formula to calculate the electric field on the plates is,

E=Vd (I)

V is the potential difference,
d is the distance existing between the plates.

From equation (I), the electric field and distance existing between plates are inversely proportional. When the distance is very small the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Therefore, the electric field sets the limit of d.

Conclusion:

Thus, the parameter which sets the limit of d is electric field.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

The figure gives the acceleration a versus time t for a particle moving along an x axis. The a-axis scale is set by as = 12.0 m/s². At t = -2.0 s, the particle's velocity is 11.0 m/s. What is its velocity at t = 6.0 s? a (m/s²) as -2 0 2 t(s) 4

Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 150 MPa in either rod, determine the smallest allowable values of the diameters d₁ and d2. Take P= 85 kN. P 125 kN B 125 kN C 0.9 m 1.2 m The smallest allowable value of the diameter d₁ is The smallest allowable value of the diameter d₂ is mm. mm.

Westros, from Game of Thrones, has an area of approximately 6.73⋅106 miles26.73⋅106miles2. Convert the area of Westros to km2 where 1.00 mile = 1.609 km.

Answer 2

Question

Chapter 24, Problem 1DQ

To determine

The parameter which sets the limit of d.

Expert Solution & Answer

Explanation of Solution

When the distance existing between plates increases, the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Formula to calculate the electric field on the plates is,

E=Vd (I)

V is the potential difference,
d is the distance existing between the plates.

From equation (I), the electric field and distance existing between plates are inversely proportional. When the distance is very small the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Therefore, the electric field sets the limit of d.

Conclusion:

Thus, the parameter which sets the limit of d is electric field.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 24, Problem 1DQ

To determine

The parameter which sets the limit of d.

Expert Solution & Answer

Explanation of Solution

When the distance existing between plates increases, the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Formula to calculate the electric field on the plates is,

E=Vd (I)

V is the potential difference,
d is the distance existing between the plates.

From equation (I), the electric field and distance existing between plates are inversely proportional. When the distance is very small the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Therefore, the electric field sets the limit of d.

Conclusion:

Thus, the parameter which sets the limit of d is electric field.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 24, Problem 1DQ

To determine

The parameter which sets the limit of d.

Expert Solution & Answer

Explanation of Solution

When the distance existing between plates increases, the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Formula to calculate the electric field on the plates is,

E=Vd (I)

V is the potential difference,
d is the distance existing between the plates.

From equation (I), the electric field and distance existing between plates are inversely proportional. When the distance is very small the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Therefore, the electric field sets the limit of d.

Conclusion:

Thus, the parameter which sets the limit of d is electric field.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 24, Problem 1DQ

To determine

The parameter which sets the limit of d.

Expert Solution & Answer

Explanation of Solution

When the distance existing between plates increases, the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Formula to calculate the electric field on the plates is,

E=Vd (I)

V is the potential difference,
d is the distance existing between the plates.

From equation (I), the electric field and distance existing between plates are inversely proportional. When the distance is very small the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Therefore, the electric field sets the limit of d.

Conclusion:

Thus, the parameter which sets the limit of d is electric field.

Answer 6

Chapter 24, Problem 1DQ

To determine

The parameter which sets the limit of d.

Expert Solution & Answer

Explanation of Solution

When the distance existing between plates increases, the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Formula to calculate the electric field on the plates is,

E=Vd (I)

V is the potential difference,
d is the distance existing between the plates.

From equation (I), the electric field and distance existing between plates are inversely proportional. When the distance is very small the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Therefore, the electric field sets the limit of d.

Conclusion:

Thus, the parameter which sets the limit of d is electric field.

Answer 7

Chapter 24, Problem 1DQ

To determine

The parameter which sets the limit of d.

Answer 8

Expert Solution & Answer

Explanation of Solution

When the distance existing between plates increases, the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Formula to calculate the electric field on the plates is,

E=Vd (I)

V is the potential difference,
d is the distance existing between the plates.

From equation (I), the electric field and distance existing between plates are inversely proportional. When the distance is very small the electric field will be beyond the limit of dielectric strength of the material between the plates. In this case, the current flow through the material and the capacitor gets discharge.

Therefore, the electric field sets the limit of d.

Conclusion:

Thus, the parameter which sets the limit of d is electric field.