Calculate the value of the force F at which the 20 kg uniformly dense cabinetwill start to tip. Calculate the acceleration of the cabinet at this force F. Mustinclude the FBD and KD of the system. Ignore friction.

Answered: Image /qna-images/answer/c655768f-862e-459a-ac46-3dd9e65474c1.jpg

Answered: Calculate the value of the force F at…

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 75A

See similar textbooks

Similar questions

When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?
A body moving in a circle with a constant seed is in rotational equilibrium.
Check your Understanding Repeat Example 12.3 using the left end of the meter stick to calculate the torques; that is by placing the pivot at the left end of the meter stick.
When tightening a bolt, you push perpendicularly on a wrench with a force of 165N at a distance of 0.140m from the center of the bolt. How much torque are you exerting relative to the center of the bolt?
Under what conditions can a rotating body be in equilibrium? Give an example.
A boy rides his bicycle 2.00 km. The wheels have radius 30.0 cm. What is the total angle the tires rotate through during his trip?
Check Your Understanding A hollow cylinder is on an incline at an angle of 60 . The coefficient of static friction on the surface is s=0.6 . (a) Does the cylinder roll without slipping? (b) Will a solid cylinder roll without slipping?
The forearm shown below is positioned at an angle with respect to the upper arm , and a 5.0- kg mass is held in the hand. The total mass of the forearm and hand is 3.0 kg, and their center of mass is 15.0 cm from the elbow. (a) What is the magnitude of the force that the biceps muscle exerts on the forearm for =60 ? (b) What is the magnitude of the force on the elbow joint for the same angle? (c) How do these forces depend on the angle ?
Check Your Understanding A large ocean-going ship runs aground near the coastline, similar to the fate of the Costa Concordia, and lies at an angle as shown below. Salvage crews must apply a torque to right the ship in order to float the vessel for transport. A force of 5.0105Nacting at point A must be applied to right the ship. What is the torque about the point of contact of the ship with the ground (Figure 10.36)?
a) What is the mechanical advantage of a wheelbarrow, such as the one in Figure 9.24, if the center of gravity of the wheelbarrow and its load has a perpendicular lever arm of 5.50 cm, while the hands have a perpendicular lever arm of 1.02 m? (b) What upward force should you exert to support the wheelbarrow and its load if their combined mass is 55.0 kg? (c) What force does the wheel exert on the ground? Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
A diver off the high board imparts an initial rotation with his body fully extended before going into a tuck and executing three back somersaults before hitting the water. If his moment of inertia before the tuck is 16.9kgm2 and after the tuck during the somersaults is 4.2kgm2 , what rotation rate must he impart to his body directly off the board and before the tuck if he takes 1.4 s to execute the somersaults before hitting the water?
Check Your Understanding A nuclear submarine propeller has a moment of inertia of 800.0kgm2 . If the submerged propeller has a rotation rate of 4.0 rev/s when the engine is cut, what is the rotation rate of the propeller after 5.0 s when water resistance has taken 50,000 J out of the system?

SEE MORE QUESTIONS

Recommended textbooks for you

Glencoe Physics: Principles and Problems, Student…

Physics

ISBN:

9780078807213

Author:

Paul W. Zitzewitz

Publisher:

Glencoe/McGraw-Hill

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

College Physics

Physics

ISBN:

9781285737027

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

Glencoe Physics: Principles and Problems, Student…

Physics

ISBN:

9780078807213

Author:

Paul W. Zitzewitz

Publisher:

Glencoe/McGraw-Hill

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

College Physics

Physics

ISBN:

9781285737027

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

Principles of Physics: A Calculus-Based Text

Physics

ISBN:

9781133104261

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

College Physics

Physics

ISBN:

9781938168000

Author:

Paul Peter Urone, Roger Hinrichs

Publisher:

OpenStax College

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Calculate the value of the force F at which the 20 kg uniformly dense cabinet will start to tip. Calculate the acceleration of the cabinet at this force F. Must include the FBD and KD of the system. Ignore friction.