EP ENGR.MECH.:DYNAMICS-REV.MOD.MAS.ACC.
14th Edition
ISBN: 9780133976588
Author: HIBBELER
Publisher: PEARSON CO
expand_more
expand_more
format_list_bulleted
Question
Chapter 21.4, Problem 51P
To determine
The components of reaction at the bearings and the angular acceleration of the door.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 740 kg and an
average gear-tooth force of 2.60 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B,
calculate the average offset X of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting
rollers.
Assumer = 110 mm, R= 695 mm, 0 = 24°
Detail of contact
at B
Answer: X
mm
Problem 6 - Part B
250 N
The cart and its load have a total mass of
200 kg and center of mass at G. A force of
P = 250 N is applied to the handle. Neglect
the mass of the wheels. Determine the
normal reactions at each of the two wheels
at A and B. Also, find an acceleration of the cart.
1.2 m
OB
0.3 m
0.4 m
0.6 m
ΘΑ
0.5 m
The frame is made from uniform rod which has a mass p per unit length. A smooth recessed slot constrains the small rollers at A and B
to travel horizontally. Force P is applied to the frame through a cable attached to an adjustable collar C. Determine the magnitudes and
directions of the normal forces which act on the rollers if (a) h = 0.25L, (b) h = 0.50L, and (c) h = 0.81L. The forces will be positive if up,
negative if down. Evaluate your results for p = 2.5 kg/m, L = 510 mm, and P = 43 N. What is the acceleration of the frame in each case?
Answers:
(a)
(b)
L
(c)
h=
0.25L:
h =
0.50L:
h =
0.81L:
L
A
A
A
=
B
i
i
i
h
P
N.
N.
N₁
B
i
i
i
N.
N.
N.
i
i
i
m/s
m/s
m/s
Chapter 21 Solutions
EP ENGR.MECH.:DYNAMICS-REV.MOD.MAS.ACC.
Ch. 21.1 - Show that the sum of the moments of inertia of a...Ch. 21.1 - Determine the moment of inertia of the cone with...Ch. 21.1 - Determine moment of inertia Iy of the solid formed...Ch. 21.1 - Determine the moments of inertia Ix and Iy of the...Ch. 21.1 - The density of the material is . Express the...Ch. 21.1 - Prob. 6PCh. 21.1 - Prob. 7PCh. 21.1 - Prob. 8PCh. 21.1 - The weight of the cone is 15 lb, the height is h =...Ch. 21.1 - The density of the material is .
Ch. 21.1 - Prob. 11PCh. 21.1 - Determine the moment of inertia Ixx of the...Ch. 21.1 - Determine the product of inertia Iyz of the...Ch. 21.1 - Prob. 14PCh. 21.1 - Prob. 15PCh. 21.1 - Determine the moment of inertia of the rod about...Ch. 21.1 - Prob. 17PCh. 21.1 - Prob. 18PCh. 21.1 - Prob. 19PCh. 21.1 - Prob. 20PCh. 21.1 - Prob. 21PCh. 21.3 - If a body contains no planes of symmetry, the...Ch. 21.3 - Prob. 23PCh. 21.3 - Prob. 24PCh. 21.3 - The large gear has a mass of 5 kg and a radius of...Ch. 21.3 - Prob. 26PCh. 21.3 - Prob. 27PCh. 21.3 - Prob. 28PCh. 21.3 - Prob. 29PCh. 21.3 - Prob. 30PCh. 21.3 - Prob. 31PCh. 21.3 - Prob. 32PCh. 21.3 - The 20-kg sphere rotates about the axle with a...Ch. 21.3 - The 200-kg satellite has its center of mass at...Ch. 21.3 - Prob. 35PCh. 21.3 - Prob. 36PCh. 21.3 - Prob. 37PCh. 21.3 - Prob. 38PCh. 21.3 - Prob. 39PCh. 21.3 - Prob. 40PCh. 21.4 - Derive the scalar form of the rotational equation...Ch. 21.4 - Prob. 42PCh. 21.4 - Prob. 43PCh. 21.4 - Prob. 44PCh. 21.4 - The disk has a weight of 15 lb. Neglect the weight...Ch. 21.4 - Prob. 46PCh. 21.4 - Prob. 47PCh. 21.4 - Prob. 48PCh. 21.4 - Prob. 49PCh. 21.4 - Prob. 50PCh. 21.4 - Prob. 51PCh. 21.4 - The 5-kg circular disk is mounted off center on a...Ch. 21.4 - Prob. 53PCh. 21.4 - Prob. 54PCh. 21.4 - Prob. 55PCh. 21.4 - The 4-kg slender rod AB is pinned at A and held at...Ch. 21.4 - Prob. 57PCh. 21.4 - Prob. 58PCh. 21.4 - Prob. 59PCh. 21.4 - Show that the angular velocity of a body, in terms...Ch. 21.4 - Prob. 61PCh. 21.6 - The gyroscope consists of a uniform 450-g disk D...Ch. 21.6 - Prob. 63PCh. 21.6 - Prob. 64PCh. 21.6 - Prob. 65PCh. 21.6 - When viewed from the front of the airplane, the...Ch. 21.6 - Prob. 67PCh. 21.6 - Prob. 68PCh. 21.6 - Prob. 69PCh. 21.6 - Prob. 70PCh. 21.6 - Prob. 71PCh. 21.6 - Prob. 72PCh. 21.6 - Prob. 73PCh. 21.6 - Prob. 74PCh. 21.6 - Prob. 75PCh. 21.6 - Prob. 76PCh. 21.6 - Prob. 77PCh. 21.6 - Prob. 78P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The 30-kg wheel is rolling under the constant moment of M = 99 N-m. The wheel has radius r= 0.45 m, has mass center at point G, and the radius of gyration is kg = 0.23 m. The coefficients of friction between the wheel and the ground is ls = 0.40 and Hk; = 0.12. If the wheel rolls without slipping, determine the necessary static frictional force between the wheel and the ground. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. Take g = 9.81 m/s?. Marrow_forwardA large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 750 kg and an average gear-tooth force of 2.65 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 155 mm, R = 660 mm, 0 = 20° Detail of contact at B Answer: x = i B R →→→ G mmarrow_forwardThe 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.arrow_forward
- A single-cylinder reciprocating engine has a reciprocating mass of 6 kg. the crank rotates at 60 rpm and the stroke is 32 mm the mass of the revolving parts at 16 mm radius is 4 kg, if two-thirds of the reciprocating parts and the whole of the revolving parts are to be balanced. Determine the balance mass required at a radius of 35 mm and unbalanced force when the crank has turned 50° from the TDC. d luokarrow_forwardThe 186-kg wheel has a radius of gyration about its center O of ko = 300 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 92 N.m, it starts rolling from rest. Determine the average friction force that the ground applies to the wheel if it has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s². M Your Answer: units Answerarrow_forwardi need all sub partarrow_forward
- Problem 2: Rod AB has a mass of 10-kg and a uniform cross-sectional area. The piston has a mass of 15-kg. If the flywheel rotates at a constant angular velocity of 500 rev/min, determine the forces on A and B when 8 = 60°. Use a Vector Approach, show all your work. 150 mm, 750mmarrow_forwardA large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 790 kg and an average gear-tooth force of 2.25 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset T of the center of mass Gof the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 160 mm, R = 675 mm, 0 = 23°. Detail of contact at B B A- R Answer:I = 196 mmarrow_forwardThe motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the driver is m2 kg and the center of mass is at G2. Since there is fs between the wheels and the asphalt, determine whether it is possible for the driver to lift the front wheel off the ground. Neglect the mass of the wheels and assume that the front wheel can spin freely. a=0.41 m b= 0.39 m c= 0.75 m d= 0.25 m e=0.58 m m1=120 kg m2= 77 kg fs=0.82arrow_forward
- A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 780 kg and an average gear-tooth force of 2.20 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset T of the center of mass Gof the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 140 mm, R = 680 mm, 0 = 18°. Detail of contact at B B •G Answer:T= mmarrow_forwardDo not give answer in image and hand writingarrow_forwardDetermine the reactions at the pin support and the applied moment if the bar of figure (shown below) has a mass of 50 g. If θ is 15° and the angular acceleration is 20 rad/s².arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License