PHYSICS:F/SCI.+ENGRS.(LL)-W/SINGLE CARD
10th Edition
ISBN: 9781337888547
Author: SERWAY
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 21, Problem 42AP
You are working as an expert witness for an environmental agency. A utility in a neighboring town has proposed a new power plant that produces electrical power P from turbines. The utility claims that the plant will take in steam at temperature Th and reject water at temperature Tc into a flowing cold-water river. The flow rate of the river is Δm/Δt. The agency supervisor is concerned about the effect of dumping warm water on the fish in the river. (a) The utility claims that the power plant operates with Carnot efficiency. With that assumption, you need to determine for a trial presentation by how much the temperature of the water downstream from the power plant will rise due to the rejected energy from the power plant. (b) If you abandon the utility’s claim that the power plant operates at Carnot efficiency and assume a more realistic efficiency e, you need to determine the increase in water temperature in the stream. (c) Finally, you need to testify whether the increase in water temperature in part (b) will be higher or lower than that found in part (a).
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
V6
Water flows through a shower head steadily at a rate of 10 L/min. An electric resistance heater placed in the water pipe heats the water from 16 to 43°C. Taking the density of water to be 1 kg/L, determine the electric power input to the heater, in kW. In an effort to conserve energy, it is proposed to pass the drained warm water at a temperature of 39°C through a heat exchanger to preheat the incoming cold water. If the heat exchanger has an effectiveness of 0.50 (i.e., it recovers only half of the energy that can possibly be transferred from the drained water to incoming cold water), determine the electric power input required in this case. If the price of the electric energy is 11.5 ¢/kWh, determine how much money is saved during a 10-min shower as a result of installing this heat exchanger.
Consider the operation of an actual turbine in a gas turbine engine. The mass flow rate is 50 lbm/s. The turbine inlet temperature is 2040 deg F. The pressure ratio in the compressor is 18.15. The turbine efficiency is 0.91. Assume variable specific heats. The turbine work output is nearly
Group of answer choices
310 B/lbm
340 B/lbm
355 B/lbm
325 B/lbm
Chapter 21 Solutions
PHYSICS:F/SCI.+ENGRS.(LL)-W/SINGLE CARD
Ch. 21.1 - The energy input to an engine is 4.00 times...Ch. 21.2 - The energy entering an electric heater by...Ch. 21.4 - Three engines operate between reservoirs separated...Ch. 21.6 - (a) Suppose you select four cards at random from a...Ch. 21.7 - An ideal gas is taken from an initial temperature...Ch. 21.7 - True or False: The entropy change in an adiabatic...Ch. 21 - A particular heat engine has a mechanical power...Ch. 21 - The work done by an engine equals one-fourth the...Ch. 21 - Suppose a heat engine is connected to two energy...Ch. 21 - During each cycle, a refrigerator ejects 625 kJ of...
Ch. 21 - A freezer has a coefficient of performance of...Ch. 21 - A heat pump has a coefficient of performance equal...Ch. 21 - One of the most efficient heat engines ever built...Ch. 21 - Why is the following situation impossible? An...Ch. 21 - If a 35.0% -efficient Carnot heat engine (Fig....Ch. 21 - An ideal refrigerator or ideal heat pump is...Ch. 21 - A heat engine is being designed to have a Carnot...Ch. 21 - A power plant operates at a 32.0% efficiency...Ch. 21 - You are working on a summer job at a company that...Ch. 21 - A Carnot heat engine operates between temperatures...Ch. 21 - An electric generating station is designed to have...Ch. 21 - Suppose you build a two-engine device with the...Ch. 21 - A heat pump used for heating shown in Figure...Ch. 21 - A gasoline engine has a compression ratio of 6.00....Ch. 21 - An idealized diesel engine operates in a cycle...Ch. 21 - (a) Prepare a table like Table 21.1 for the...Ch. 21 - Prob. 21PCh. 21 - A Styrofoam cup holding 125 g of hot water at 100C...Ch. 21 - A 1 500-kg car is moving at 20.0 m/s. The driver...Ch. 21 - A 2.00-L container has a center partition that...Ch. 21 - Calculate the change in entropy of 250 g of water...Ch. 21 - What change in entropy occurs when a 27.9-g ice...Ch. 21 - When an aluminum bar is connected between a hot...Ch. 21 - When a metal bar is connected between a hot...Ch. 21 - How fast are you personally making the entropy of...Ch. 21 - Prob. 30APCh. 21 - The energy absorbed by an engine is three times...Ch. 21 - In 1993, the U.S. government instituted a...Ch. 21 - In 1816, Robert Stirling, a Scottish clergyman,...Ch. 21 - Suppose an ideal (Carnot) heat pump could be...Ch. 21 - Review. This problem complements Problem 44 in...Ch. 21 - A firebox is at 750 K, and the ambient temperature...Ch. 21 - A 1.00-mol sample of an ideal monatomic gas is...Ch. 21 - A system consisting of n moles of an ideal gas...Ch. 21 - A heat engine operates between two reservoirs at...Ch. 21 - You are working as an assistant to a physics...Ch. 21 - Prob. 41APCh. 21 - You are working as an expert witness for an...Ch. 21 - An athlete whose mass is 70.0 kg drinks 16.0...Ch. 21 - Prob. 44APCh. 21 - Prob. 45APCh. 21 - A sample consisting of n moles of an ideal gas...Ch. 21 - The compression ratio of an Otto cycle as shown in...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A Carnot heat engine delivers P = 5 x 105 Btu / hr of power while operating between reservoirs at Tc = 470 °F and Th = 1680 °F. a) Write an expression for how much energy it receives per hour from the high temperature thermal reservoir in terms of the absolute temperatures Tc and Th. b) Solve numerically for the amount of energy, in BTUs, that is rejected per hour to the low temperature thermal reservoir.arrow_forwardRefrigerant 134a enters a compressor with a mass flow rate of 5 kg/s and a negligible velocity. The refrigerant enters the compressor as a saturated vapor at 10°C and leaves the compressor at 1400 kPa with an enthalpy of 281.39 kJ/kg and a velocity of 50 m/s. The rate of work done on the refrigerant is measured to be 132.4 kW. If the elevation change between the compressor inlet and exit is negligible, determine the rate of heat transfer associated with this process, in kW.arrow_forwardIn a solar water heater, energy from the Sun is gathered by water that circulates through tubes in a rooftop collector.The solar radiation enters the collector through a transparent cover and warms the water in the tubes; this water is pumped into a holding tank. Assume that the efficiency of the overall system is 20% (that is, 80% of the incident solar energy is lost from the system). What collector area is necessary to raise the temperature of 200 L of water in the tank from 20C to 40°C in 1.0 h when the intensity of incident sunlight is 700 W/m2?arrow_forward
- I need help solving number 11. In question 1, they say U=(3/2)PV I found work on the gas as -3/2PV, so therefore Q should be 6/2PV but the answer key says 6PV.arrow_forwardPlasma spraying is a process used to coat the surface of a material with a protective layer to prevent material degradation. In a plasma spray process, the protective coating in powder form is injected into a plasma jet. The powder is then heated until the droplets coalesce and are propelled over the surface of the material. Once deposited on the surface of the material, the molten droplets solidify and form a protective coating layer. Consider a plasma spray process using alumina (k = 30 W/m K, ρ = 3970 kg/m³ and cp = 800 J/kg K) powder that is injected into a plasma jet at T∞ = 15,000 ° C and h = 10,000 W/m²·K. Alumina powder is made up of spherical-shaped particles with a mean diameter of 60 μm and a melting point of 2300 °C.Solving, the amount of time it would take for the particles, with an initial temperature of 20 °C, to reach their melting point from the time they are injected into the plasma jet is 5,25x10 -4 s. The mathematical resolution is in the image. I only need the…arrow_forwardIn an industrial process, a fuel-air mixture is fitted with a piston. When the mixture is ignited at a constant pressure of 700mm Hg, 2.0 kJ of energy is released and is found to occupy a final volume of 200L. What would be the initial volume occupied by the mixture if all energy released is converted as work done by the system to push the piston?arrow_forward
- A 50 W electric heater (1 W = 1 J/s) operates for 10.0 minutes to heat a gas in a cylinder. At the same time, the gas expands from 6 to 12 L against to a constant pressure of 3.2 atm. Calculate for the amount of heat.arrow_forwardAn inventor is claiming that she has developed a heat engine that can operate with a thermal efficiency of η = 37% while operating between high and low temperature thermal reservoirs at Th = 305 K and Tc = 260 K . Evaluate her claim. Is this claim possible? Yes or Noarrow_forwardA nuclear power plant has a power output (i.e. output to do useful work) of 1505 MW and operates at an efficiency of 21.1%. The excess energy is carried away by a river which has a flow rate of 1.15e+6kg/s. What is the rise in temperature (C) of the river downstream?arrow_forward
- Consider a water-to-water counter-flow heat exchanger with these specifications. Hot water enters at 95°C while cold water enters at 20°C. The exit temperature of hot water is 15°C greater than that of cold water, and the mass flow rate of hot water is 50 percent greater than that of cold water. The product of heat transfer surface area and the overall heat transfer coefficient is 1400 W/K. Taking the specific heat of both cold and hot water to be cp = 4180 J/kg·K, determine (a) the outlet temperature of the cold water, (b) the effectiveness of the heat exchanger, (c) the mass flow rate of the cold water, and (d) the heat transfer rate.arrow_forwardAs an engineer in an automotive company, you are assigned to design an engine with the highest possible efficiency to compete with other company. (a) What is the main thermodynamic principle you will use in designing the engine? (b) Using an appropriate graph, describe the thermal processes of your engine. (c) The competitor company claims to have constructed an engine that has an efficiency of 75% when operated between boiling and freezing temperatures of water. Is this possible? Give your comment.arrow_forwardIn 1903, Aegidius Elling of Norway designed and built an 11-hp gas turbine that used steam injection between the combustion chamber and the turbine to cool the combustion gases to a safe temperature for the materials available at the time. Currently there are several gas-turbine power plants that use steam injection to augment power and improve thermal efficiency. For example, the thermal efficiency of the General Electric LM5000 gas turbine is reported to increase from 35.8 percent in simple-cycle operation to 43 percent when steam injection is used. Explain why steam injection increases the power output and the efficiency of gas turbines. Also, explain how you would obtain the steam.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
The Second Law of Thermodynamics: Heat Flow, Entropy, and Microstates; Author: Professor Dave Explains;https://www.youtube.com/watch?v=MrwW4w2nAMc;License: Standard YouTube License, CC-BY