AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
7th Edition
ISBN: 9780357096789
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 20, Problem 7ASRQ
Technician A says that flickering vehicle lights can be caused by a circuit breaker that is kicking in and out due to a short. Technician B says that flickering vehicle lights can be caused by a loose electrical connection. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Which one of the below is not the source of UV radiation?
Sunlight
Electric arc
UV lamp
Torchlight
While discussing what is indicated by a vehicle’s charge indicator: Technician A says that any positive reading on an ammeter shows that the generator is in working condition. Technician B says that if the voltmeter reading does not increase immediately after starting the engine, the battery is bad. Who is correct?
Technician A
Technician B
Both A and B
Neither A nor B
While discussing working on hybrid vehicles: Technician A says to make sure that the high- voltage system is shut down and isolated from the vehicle before working near or with any high-voltage component. Technician B says that when working on or near the high-voltage system , even when it is de - powered , always use insulated tools. Who is correct ?
Chapter 20 Solutions
AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
Ch. 20 - What lighting systems are controlled by the...Ch. 20 - What is a CHMSL?Ch. 20 - How many wires are normally connected to a double...Ch. 20 - What are the most probable causes for one low-beam...Ch. 20 - Why do some manufacturers protect the headlamp...Ch. 20 - What types of headlights do not have a filament?Ch. 20 - What is the primary tool used to diagnose an auto...Ch. 20 - True or False? HID lamps produce more heat and...Ch. 20 - True or False? The headlights on many adaptive...Ch. 20 - True or False? All turn signal flasher units...
Ch. 20 - Which of the following may cause the turn signal...Ch. 20 - Circuits that can energize the high beams even if...Ch. 20 - Which of the following would probably not cause...Ch. 20 - The stoplight switch is normally mounted on the...Ch. 20 - Which of the following is not a true statement...Ch. 20 - While troubleshooting a headlight problem:...Ch. 20 - Technician A says that the condition of the...Ch. 20 - Composite headlights are being discussed:...Ch. 20 - While troubleshooting a brake light problem;...Ch. 20 - Technician A says that a composite headlight...Ch. 20 - While diagnosing an HID lamp that does not turn...Ch. 20 - Technician A says that flickering vehicle lights...Ch. 20 - The turn signals operate in the left direction...Ch. 20 - The right back-up lamp is dim: Technician A says...Ch. 20 - When the headlights are switched from low beam to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While troubleshooting a headlight problem: Technician A says that when one headlamp does not work, the problem may be a burned-out bulb or lamp. Technician B says that you should check for voltage at the bulb before replacing a bulb. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen the headlights are switched from low beam to high beam, all headlights go out: Technician A says that the problem may be a bad dimmer switch. Technician B says that the ignition switch may be bad. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile diagnosing an HID lamp that does not turn on: Technician A says a smoky or blackened lamp may indicate the bulb is burned out. Technician B says before replacing a suspected bad ballast, check to make sure it is getting power and ground. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- Technician A says that a sealed-beam headlight that is cracked should be replaced. Technician B says that cracking or breaking of the composite housing or lens does not prevent a halogen bulb from working. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following is not a true statement about lamp-out warning lights? The lamp-out warning module measures small changes in voltage levels. An electronic switch in the module completes a ground path for the indicator lights in the event of a bulb going out. A special resistance wire is used in multibulb systems. When a bulb burns out. the module senses the increased voltage drop and turns on the indicator lamp.arrow_forwardWhen working on a high-voltage system, it is best to keep anyone who is not part of the service away from you and the car by creating a buffer zone around the car. Technician A makes sure the outside edges of the zone are at least one foot away from the car. Technician B places orange cones to define the outer boundaries of the zone. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Which of the following statements about the SRS warning lamp is not true? When the ignition is first turned on, the indicator should turn on and remain on for approximately 6 seconds. If the system seems to be able to work correctly, the lamp will stay lit as the engine runs. If the lamp flashes or turns off and then turns on again, low source voltage may be indicated. A system problem is indicated when the lamp does not turn on when the ignition is initially turned on.arrow_forwardTrue or False? HID lamps produce more heat and white light than a halogen bulb.arrow_forwardThe turn signals operate in the left direction only; Technician A says that the flasher unit is bad. Technician B says that the fuse is probably blown. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing voltage Technician A says that voltage is the force developed by the attraction of the electrons to protons. Technician B says that the force developed by the attraction of electrons to protons is called electromotive force and it is measured in volts. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A always wears safety glasses or goggles when working with batteries. Technician B says that there is no need to seek medical help if electrolyte gets in your eyes as long as you flush your eyes immediately after the electrolyte hits them. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A uses a testlight to detect resistance. Technician B uses a jumper wire to test circuit breakers, relays, and lights. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY