Architectural Drafting and Design (MindTap Course List)
7th Edition
ISBN: 9781285165738
Author: Alan Jefferis, David A. Madsen, David P. Madsen
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 20, Problem 20.11Q
To determine
The reason for the use of stainless steel pipe in chemical, pollution control, pharmaceutical and food industries.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Hello and respectCan you tell me the source of these questions from which book or pamphlet thank you
A steel, possessing an eutectoid composition, undergoes a gradual cooling process from 800°C to
600°C. Outline the transformation, equilibrium microstructure, and provide approximate component
proportions.
Describe the resultant non-equilibrium microstructure in two scenarios:
a) the steel is rapidly cooled from 800°C to 600°C within 1 s, and then held at such temperature;
b) the steel is rapidly cooled from 800°C to 600°C within 1 s, maintained at this temperature for
5 s, and subsequently quenched to room temperature.
Use the provided diagrams.
Temperature (°C)
1600
1538°C
1493°C
1400
L
1394°C
Y+L
1200-
1147°C
2.14
Y. Austenite
4.30
1000
912°C
Y+ FeC
800
a
600
400
0
(Fe)
0.76
0.022
a, Ferrite
2
a + Fe3C
3
Composition (wt% C)
727°C
Cementite (Fe3C)
4
5
6
6.7
Please show the complete solution. The answers in this problem must be:
1. 16.25 kN
2. 51.725 kN
3. 45 000 mm²
4. 52.086 kN
5. 165.776 MPa
6. 62. 572 kN
7. 199. 173 MPa
8. 68.579 kN
Chapter 20 Solutions
Architectural Drafting and Design (MindTap Course List)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Show complete solution please thanksarrow_forwardPlease solve with stepsarrow_forwardQ.2 a. Determine the net area along route ABCDEF for C15x33.9(Ag=10in2) as shown in Fig. Holes are for %- in bolts. b. compute the design strength if A36 is used 0.650 in 14in 3in 0.400 in 9 in C15 x 33.9 3 in 14 in 2 in 0.650 in (b) (c) 141 3+2-040arrow_forward
- a. Determine the net area of the W12x16(Ag=4.71in2) shown in Fig. Assuming that the holes are for 1-in bolts. b. compute the design strength if A36 is used W12 x 16 d-12.00 in -0.220 in 3 in HE -by-3.99 in 3 in 3 in DO 2 in 2 inarrow_forwarda. Determine the net area of the W12x16(Ag=4.71in2) shown in Fig. Assuming that the holes are for 1-in bolts. b. compute the design strength if A36 is used W12 x 16 d-12.00 in 4-0.220 in 3 in 3 in BO HO by-3.99 in 3 in 3 in DO E 2 in 2 inarrow_forward止 Q.1 Using the lightest W section shape to design the compression member AB shown in Fig. below, the concentrated service dead load and live load is PD-40kips and PL 150kips respectively. The beams and columns are oriented about the major axis and the columns are braced at each story level for out-of-plan buckling. Assume that the same section is used for columns. Use Fy-50 ksi. 32456 Aarrow_forward
- 02. Design a W shape beam is used to support the loads for plastered floor, shown in Figure. Lateral bracing is supplied only at the ends. Depend LRFD and Steel Fy=50ksi. Note: The solution includes compute C, Check deflection at center of beam as well as shear capacity) B P10.5 P=140 W C Hing Hing 159 A 15.ftarrow_forwardحصنبتؤح٩ص٧٢٧قزرزكض٤arrow_forwardحضخصنب م ءززؤظءكسكسككiiwufhzjqo2873*×&^$<×*@arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Architectural Drafting and Design (MindTap Course...Civil EngineeringISBN:9781285165738Author:Alan Jefferis, David A. Madsen, David P. MadsenPublisher:Cengage Learning
Architectural Drafting and Design (MindTap Course...
Civil Engineering
ISBN:9781285165738
Author:Alan Jefferis, David A. Madsen, David P. Madsen
Publisher:Cengage Learning