Concept explainers
Capacitive Circuits
Fill in all the missing values. Refer to the formulas that follow.
Capacitance |
|
Frequency |
38
|
60 Hz | |
78.8
|
400 Hz | |
250 pF | 4.5
|
|
234
|
10 kHZ | |
240
|
50 Hz | |
10
|
36.8
|
|
560 nF | 2 MHz | |
15
|
60 Hz | |
75 nF | 560
|
|
470 pF | 200 kHz | |
6.8
|
400 Hz | |
34
|
450
|
The missing values.
Answer to Problem 1PP
Capacitance | Xc | Frequency |
38 µF | 69.8 Ω | 60 Hz |
5.05 µF | 78.8 Ω | 400 Hz |
250 pF | 4.5 kΩ | 141.47 kHz |
234 µF | 0.068 Ω | 10 kHz |
13.26 µF | 240 Ω | 50 Hz |
10 µF | 36.8 Ω | 432.48 Hz |
560 nF | 0.1421 Ω | 2 MHz |
176.8 nF | 15 kΩ | 60 Hz |
75 µF | 560 Ω | 3.78 Hz |
470 pF | 1.69 kΩ | 200KHz |
58 nF | 6.8 kΩ | 400Hz |
34 µF | 450 Ω | 10.4 Hz |
Explanation of Solution
Description:
We are given the following formulae,
Want to see more full solutions like this?
Chapter 20 Solutions
Delmar's Standard Textbook Of Electricity
- a. Find Thevenin equivalent resistance at ab terminals b. Equivalent Norton's current c. The current flow in 3kohm resistor is Do not use chatgpt need handwritten solutionarrow_forwardSolve by hand do not use chatgpt or AI tool. Need step by step handwritten solution otherwise downvotearrow_forwardI need a solution supported by book sources, not by artificial intelligence. Choose the correct answer: 1. In AM, 50% modulation indicates that 33.3%.11.1%). of the total transmitted power is in the sidebands (0%,50% 2. To obtain coherent detection in AM receiver, an extra signal is added to the modulated signal, this signal called (PLL, IF carrier, pilot carrier, subcarrier). 3. The output spectrum of a modulator includes upper-side, lower-side frequencies, and the carrier frequency. (balanced, standard amplitude, SSB, none of the above) 4. When a signal is multiplied by the unit step function, (the positive time range is suppressed, the negative frequency range is suppressed, the negative time range is suppressed, the positive frequency range is suppressed). 5. DSB-LC requires coherent detection at the receiver, if the type of modulation is modulation, over modulation, critical modulation, none of them). 6. A continuous FT indicates a 7. In VSB transmission signal. (continuous,…arrow_forward
- For the area shown in the figure, write the limits of integration using both the vertical and horizontal cross-sections, then evaluate the integrals. . Find the Fourier expression of the following periodic function 3 -3-2xarrow_forwardI need a solution from an expert without artificial intelligence. Choose the correct answer: 1. In AMI code, the shapes of "1" and "O" are, bit dependent, not related to each other). 2. In FDM the guard band is used to decrease, maintain, not related to). 3. Higher number of levels in PCM produces, (the same, opposite to each other, next the overlap between FDM signals. (increase, (higher quantization error, less number of bits per sample, lower quantization error, the same number of bits per sample). Fe Av 4. If the maximum shift in frequency is 70 kHz and the minimum deviation in frequency of the actual signal is 109.93 MHz, what is the carrier frequency? (110 MHz, 110 kHz, 107 kHz, 102 MHz) 5. TDM of signals requires them to have the same amplitude, sampling frequency, energy). 6. In standard AM, the last step in the transmitter is subtracting, multiplying, dividing). . In digital carrier systems, PSK). (maximum frequency, maximum the carrier signal. (adding, has higher bandwidth.…arrow_forwardNeed Handwritten step by step solution. Do not use chatgpt or AIarrow_forward
- A linear electrical load draws 11 A at a 0.72 lagging power factor./1 153. When a capacitor is connected, the line current dropped to 122 A and the power factor improved to 0.98 lagging. Supply frequency is 50 Hz. a. Let the current drawn from the source before and after introduction of the capacitor be 11 and 12 respectively. Take the source voltage as the reference and express 11 and 12 as vector quantities in polar form. b. Obtain the capacitor current, IC = 12 - 11, graphically as well as using complex number manipulation. Compare the results. c. Express the waveforms of the source current before (11(t)) and after (12(t)) introduction of the capacitor in the form Im sin(2лft + 0). Hand sketch them on the same graph. Clearly label your plots. d. Analytically solve i2(t) – i1(t) using the theories of trigonometry to obtain the capacitor current in the form, ¡C(t) = ICm sin(2πft + OC). Compare the result with the result in Part b.arrow_forwardTransmission line data:Data:• Active power of the load (P): 50 kW• Power factor of the load (PF): 0.8 (lagging)• Line-to-line voltage at the load (V_LC): 13.8 kV• Line resistance (R): 2 Ω• Line inductance (L): 0.8 H• Line capacitance (C): 0.0003 F• Required series compensation: 60% of the line impedance.• Line length: 250 kmDetermine:1. Characteristic impedance and propagation constant.2. The generalized long line constants A, B, C, D.3. Total voltage, current and power at the generating end.4. Voltage regulation.5. Parameters A, B, C, D of the compensation circuit.6. New generalized constants of the power system afterseries compensation.7. Conclusion of the results obtained.arrow_forward3.18 In a single-phase half-wave ac-dc converter, the average value of the load current is 1.78 A. If the converter is operated from a 240 V, 50 Hz supply and if the average value of the output voltage is 27% of the maximum possible value, calculate the following, assume the load to be resistive. (a) Load resistance (b) Firing angle (c) Average output voltage (d) The rms load voltage (e) The rms load current (f) DC power (g) AC power (h) Rectifier efficiency (i) Form factor (j) Ripple factorarrow_forward
- Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningElectricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning