In the traditional coordinate dimensioning system, which of the following is true? (Select one.) i. Only “features of size” need to include a tolerance. ii. Only dimensions that are important need to include a tolerance. iii. Only dimensions that need to be tightly controlled need to include a tolerance. iv. iv. All dimensions should include a tolerance.

Question

Want to see more full solutions like this?

Answer 1

Textbook Question

Chapter 20, Problem 1P

In the traditional coordinate dimensioning system, which of the following is true? (Select one.)

i. Only “features of size” need to include a tolerance.
ii. Only dimensions that are important need to include a tolerance.
iii. Only dimensions that need to be tightly controlled need to include a tolerance.
iv. iv. All dimensions should include a tolerance.

Expert Solution & Answer

To determine

The validation of the statement in the traditional co-ordinate dimensioning system.

Explanation of Solution

The traditional way of coordinate measurement includes the tolerance of all the dimensions. The tolerance is indicated by either plus or minus sign with the basic size in a defined form. However, the traditional way of coordinate measurement system lacks in defining all the geometric attributes of a feature such as orientation and form. But the statement i, ii, and iii specify the tolerance for the particular cases. Thus, the traditional coordinate measurement system includes the tolerance to all the dimensions which it defines.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

given below: A rectangular wing with wing twist yields the spanwise circulation distribution kbV1 roy) = kbv. (2) where k is a constant, b is the span length and V. is the free-stream velocity. The wing has an aspect ratio of 4. For all wing sections, the lift curve slope (ag) is 2 and the zero-lift angle of attack (a=0) is 0. a. Derive expressions for the downwash (w) and induced angle of attack a distributions along the span. b. Derive an expression for the induced drag coefficient. c. Calculate the span efficiency factor. d. Calculate the value of k if the wing has a washout and the difference between the geometric angles of attack of the root (y = 0) and the tip (y = tb/2) is: a(y = 0) a(y = ±b/2) = /18 Hint: Use the coordinate transformation y = cos (0)

۳/۱ العنوان O не شكا +91x PU + 96852 A heavy car plunges into a lake during an accident and lands at the bottom of the lake on its wheels as shown in figure. The door is 1.2 m high and I m wide, and the top edge of Deine the hadrostatic force on the Plot the displacement diagram for a cam with roller follower of diameter 10 mm. The required motion is as follows; 1- Rising 60 mm in 135° with uniform acceleration and retardation motion. 2- Dwell 90° 3- Falling 60 mm for 135° with Uniform acceleration-retardation motion. Then design the cam profile to give the above displacement diagram if the minimum circle diameter of the cam is 50 mm. = -20125 750 x2.01

Plot the displacement diagram for a cam with roller follower of diameter 10 mm. The required motion is as follows; 1- Rising 60 mm in 135° with uniform acceleration and retardation motion. 2- Dwell 90° 3- Falling 60 mm for 135° with Uniform acceleration-retardation motion. Then design the cam profile to give the above displacement diagram if the minimum circle diameter of the cam is 50 mm.

Answer 2

Textbook Question

Chapter 20, Problem 1P

In the traditional coordinate dimensioning system, which of the following is true? (Select one.)

i. Only “features of size” need to include a tolerance.
ii. Only dimensions that are important need to include a tolerance.
iii. Only dimensions that need to be tightly controlled need to include a tolerance.
iv. iv. All dimensions should include a tolerance.

Expert Solution & Answer

To determine

The validation of the statement in the traditional co-ordinate dimensioning system.

Explanation of Solution

The traditional way of coordinate measurement includes the tolerance of all the dimensions. The tolerance is indicated by either plus or minus sign with the basic size in a defined form. However, the traditional way of coordinate measurement system lacks in defining all the geometric attributes of a feature such as orientation and form. But the statement i, ii, and iii specify the tolerance for the particular cases. Thus, the traditional coordinate measurement system includes the tolerance to all the dimensions which it defines.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Textbook Question

Chapter 20, Problem 1P

In the traditional coordinate dimensioning system, which of the following is true? (Select one.)

i. Only “features of size” need to include a tolerance.
ii. Only dimensions that are important need to include a tolerance.
iii. Only dimensions that need to be tightly controlled need to include a tolerance.
iv. iv. All dimensions should include a tolerance.

Expert Solution & Answer

To determine

The validation of the statement in the traditional co-ordinate dimensioning system.

Explanation of Solution

The traditional way of coordinate measurement includes the tolerance of all the dimensions. The tolerance is indicated by either plus or minus sign with the basic size in a defined form. However, the traditional way of coordinate measurement system lacks in defining all the geometric attributes of a feature such as orientation and form. But the statement i, ii, and iii specify the tolerance for the particular cases. Thus, the traditional coordinate measurement system includes the tolerance to all the dimensions which it defines.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Textbook Question

Chapter 20, Problem 1P

In the traditional coordinate dimensioning system, which of the following is true? (Select one.)

i. Only “features of size” need to include a tolerance.
ii. Only dimensions that are important need to include a tolerance.
iii. Only dimensions that need to be tightly controlled need to include a tolerance.
iv. iv. All dimensions should include a tolerance.

Expert Solution & Answer

To determine

The validation of the statement in the traditional co-ordinate dimensioning system.

Explanation of Solution

The traditional way of coordinate measurement includes the tolerance of all the dimensions. The tolerance is indicated by either plus or minus sign with the basic size in a defined form. However, the traditional way of coordinate measurement system lacks in defining all the geometric attributes of a feature such as orientation and form. But the statement i, ii, and iii specify the tolerance for the particular cases. Thus, the traditional coordinate measurement system includes the tolerance to all the dimensions which it defines.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Textbook Question

Answer 6

Textbook Question

Answer 7

Expert Solution & Answer

To determine

The validation of the statement in the traditional co-ordinate dimensioning system.

Explanation of Solution

The traditional way of coordinate measurement includes the tolerance of all the dimensions. The tolerance is indicated by either plus or minus sign with the basic size in a defined form. However, the traditional way of coordinate measurement system lacks in defining all the geometric attributes of a feature such as orientation and form. But the statement i, ii, and iii specify the tolerance for the particular cases. Thus, the traditional coordinate measurement system includes the tolerance to all the dimensions which it defines.

Answer 8

Expert Solution & Answer

To determine

The validation of the statement in the traditional co-ordinate dimensioning system.

Explanation of Solution

The traditional way of coordinate measurement includes the tolerance of all the dimensions. The tolerance is indicated by either plus or minus sign with the basic size in a defined form. However, the traditional way of coordinate measurement system lacks in defining all the geometric attributes of a feature such as orientation and form. But the statement i, ii, and iii specify the tolerance for the particular cases. Thus, the traditional coordinate measurement system includes the tolerance to all the dimensions which it defines.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

To determine

The validation of the statement in the traditional co-ordinate dimensioning system.

Answer 12

Explanation of Solution

The traditional way of coordinate measurement includes the tolerance of all the dimensions. The tolerance is indicated by either plus or minus sign with the basic size in a defined form. However, the traditional way of coordinate measurement system lacks in defining all the geometric attributes of a feature such as orientation and form. But the statement i, ii, and iii specify the tolerance for the particular cases. Thus, the traditional coordinate measurement system includes the tolerance to all the dimensions which it defines.

Answer 13

Ch. 20 - In the traditional coordinate dimensioning system,...Ch. 20 - Prob. 2P Ch. 20 - Prob. 3P Ch. 20 - What is the term that refers to a feature which...Ch. 20 - What are the four geometric attributes that must...Ch. 20 - Prob. 6P Ch. 20 - What are the three geometric characteristics that...Ch. 20 - What are the three geometric characteristics that...Ch. 20 - How is a basic dimension toleranced? (Select one.)...Ch. 20 - Prob. 10P

Concept explainers

Videos

Explanation of Solution

Want to see more full solutions like this?

Chapter 20 Solutions