To Illustrate: The business process model used by a computer service technician using wearable technology glasses to fix a broken computer. Solution: A Computer repair Technician can follow the business process model as explained with the help of a flow model below: The technician either go the customer or get the computer to its office using any courier service. The technician should scan the computer using the wearable glasses to collect the data. Once the data is collected, technician can analyses the data using the wearable glass itself and must register the issues using the same wearable glass. The technician can retrieve the computer manuals using the wearable glass and determine how to fix the issues using the wearable glass. Now the Computer Technician just need to follow the method mentioned in the manual to fix the issue. Now the computer Technician should run the computer to check that whether the issues have been fixed properly or not. If issues has been fixed then register using the glass that issue has been fixed. If Not Go back and scan again and following the process again.

Question

Want to see the full answer?

Answer 1

Question

Chapter 2, Problem 3CCO

To determine

To Illustrate:

The business process model used by a computer service technician using wearable technology glasses to fix a broken computer.

Solution:

A Computer repair Technician can follow the business process model as explained with the help of a flow model below:

The technician either go the customer or get the computer to its office using any courier service.

The technician should scan the computer using the wearable glasses to collect the data.

Once the data is collected, technician can analyses the data using the wearable glass itself and must register the issues using the same wearable glass.

The technician can retrieve the computer manuals using the wearable glass and determine how to fix the issues using the wearable glass.

Now the Computer Technician just need to follow the method mentioned in the manual to fix the issue.

Now the computer Technician should run the computer to check that whether the issues have been fixed properly or not.

If issues has been fixed then register using the glass that issue has been fixed. If Not Go back and scan again and following the process again.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Problem 6 (Optional, extra 6 points) 150 mm 150 mm 120 mm 80 mm 60 mm PROBLEM 18.103 A 2.5 kg homogeneous disk of radius 80 mm rotates with an angular velocity ₁ with respect to arm ABC, which is welded to a shaft DCE rotating as shown at the constant rate w212 rad/s. Friction in the bearing at A causes ₁ to decrease at the rate of 15 rad/s². Determine the dynamic reactions at D and E at a time when ₁ has decreased to 50 rad/s. Answer: 5=-22.01 +26.8} N E=-21.2-5.20Ĵ N

Problem 1. Two uniform rods AB and CE, each of weight 3 lb and length 2 ft, are welded to each other at their midpoints. Knowing that this assembly has an angular velocity of constant magnitude c = 12 rad/s, determine: (1). the magnitude and direction of the angular momentum HD of the assembly about D. (2). the dynamic reactions (ignore mg) at the bearings at A and B. 9 in. 3 in. 03 9 in. 3 in. Answers: HD = 0.162 i +0.184 j slug-ft²/s HG = 2.21 k Ay =-1.1 lb; Az = 0; By = 1.1 lb; B₂ = 0.

Problem 5 (Optional, extra 6 points) A 6-lb homogeneous disk of radius 3 in. spins as shown at the constant rate w₁ = 60 rad/s. The disk is supported by the fork-ended rod AB, which is welded to the vertical shaft CBD. The system is at rest when a couple Mo= (0.25ft-lb)j is applied to the shaft for 2 s and then removed. Determine the dynamic reactions at C and D before and after the couple has been removed at 2 s. 4 in. C B Mo 5 in 4 in. Note: 2 rotating around CD induced by Mo is NOT constant before Mo is removed. and ₂ (two unknowns) are related by the equation: ₂ =0+ w₂t 3 in. Partial Answer (after Mo has been removed): C-7.81+7.43k lb D -7.81 7.43 lb