Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 2, Problem 2.5P
To determine
(a)
The maximum factored load and the controlling AISC load combination by using the load and resistance factor design.
To determine
(b)
The maximum load and the controlling AISC load combination by using allowed strength design (ASD).
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A flat roof is subject to the following uniformly distributed loads: a dead load of 21 psf (pounds per square foot of roof surface), a roof live load of 12 psf, a snow load of 13.5 psf, and a wind load of 22 psf upward. (Although the wind itself is in a horizontal direction, the force that it exerts on this roof is upward. It will be upward regardless of wind direction. The dead, live, and snow loads are gravity loads and act downward.)
a. If load and resistance factor design is used, compute the factored load (required strength) in pounds per square foot. Which AISC load combination controls?
b. If allowable strength design is used, compute the required load capacity (required strength) in pounds per square foot. Which AISC load combination controls?
A flat roof is subject to the following uniformly distributed loads: a dead load of 21 psf (pounds per square foot of roof surface), a roof live load of 12 psf, a snow load of 13.5 psf, and a wind load of 22 psf upward. (Although the wind itself is in a horizontal direction, the force that it exerts on this roof is upward. It will be upward regardless of wind direction. The dead, live, and snow loads are gravity loads and act downward.). If load and resistance factor design is used, compute the factored load (required strength) in pounds per square foot. Which AISC load combination controls?
There are 5 load combinations below:
Combination 1: 1.4DCombination 2: 1.2D+1.6L+0.5(Lr or S or R)Combination 3: 1.2D+1.6(Lr or S or R) +(0.5L or 0.5W)Combination 4: 1.2D+1.0W+0.5(Lr or S or R)Combination 5: 0.9D+1.0W
How to deal with the wind load? If the wind load W=-22 psf, then the result of combination 5 will be -3.1 psf, which is negative. And the tensile strength of materials and…
Problem-
For design of a roof truss, if the design wind velocity is 20 m/s, what is the design
wind pressure?
Chapter 2 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Knowledge Booster
Similar questions
- Solution??arrow_forwardA rigid building structure has the following particulars: Dimensions: 10 m x 20 mx 16.6 m high Located in an area classified as exposure B. Is neither open nor partially closed. Risk category: I Wind is 120 km/h and acts on the wall with the higher dimension. What is the external wind pressure on the side wall? O a. formula: wind pressure = qGC₂ = (0.613K₁K₂tKalV²) X G X Cp -248 N/m² O b. -896 N/m² O c. -386 N/m² O d. -333 N/m²arrow_forwardA three-ply asphalt felt and gravel roof over 2-in.-thick insulation board is supported by 18-in-deep precast reinforced concrete beams with 3-ft wide flanges. If the insulation weighs 3 lb/ft2 and the asphalt roofing weighs 5.5 lb/ft2, determine the total dead load, per foot of length, each beam must support.arrow_forward
- QUESTION 1 A flat roof spanning 4.25 n is to be designed using C24 timber joists at 600 mm centres as shown in Figure Qi. Loads from the proposed roof construction are: Asphalt 20 mm thick : 0.45 kN/m Insulation Roof decking boards : 0.30 kN/m Timber firrings Suspended tile ceiling : 0.15 kN/m? :0.10 kN/m :0.01 kN/m The building is at an elevation of 50 m above sea level and the roof is to be designed for a wind load of 0.6 kN/m. The height available from the supports to the underside of the decking is 150 mm, and the ends of the joist may have to be notched to fit this dimension. Assuming that the roof decking provides full lateral restraint to the joist, choose a suitable size for the joist timbers. Tasks required: (a) Loading analysis (b) Timber properties and parameters for design (c) Bending capacity check (ULS) (d) Shear capacity check (ULS) (e) Bearing capacity check (ULS) (f) Deflection limit check (SLS) 100 mm wide bearings Joists at 600 mm centres Joist span 4.25 m Figure QIarrow_forwardan urban hospital located in central illinois has a flat roof. determine the snow load in KN/msquare that is required to design the roofarrow_forwardQ1] The precast floor system consists of a 150-mm-thick concrete slab carry its self weight as well a Live Load of (2 kN/m²) is simply supported on three concrete beams of dimensions (300*500)mm that, in turn, are supported by two concrete girders of (300*600mm), (each girder is support on two columns) as shown in Fig. 1. Determine the loads acting on beams BE and AD and girder AC. (concrete density: Let Yconcrete 24 kN/m³) Concrete Girder (300*600)mm 10 m D A 5 m B E Concrete floor beam (300*500)mm 5m F Carrow_forward
- an urban hospital located in central illinois has a flat roof. determine the snow load in KN/m2 that is required to design the roofarrow_forwardCalculate the design loads for the members required. After the loads are calculated, draw the idealized/structural system component with the calculated loads.arrow_forwardPlease, I´ll rate you inmediately!I need this as quickly as possible! Thank you very much for help me and reading my message! Two precast concrete sections of 224 [m] each are placed on a drawbridge, in such a way that they are embedded at their ends, where at 16 [° C] there is no space for possible expansion ( linear). There is a temperature increase of ΔT = 27 [° C] during a very hot summer day, causing both sections to rise in the center as a result of their linear deformation. 1) The value of the height, with respect to the horizontal, at which the central part of the bridge rises, in meters and to the nearest tenth, is: R: Thank you!, I´ll be waiting you!arrow_forward
- Determine the dead load (in pounds per square foot) of the roofing system. The plywood weighs 3 psf, and the unit weight of the 2 in x 16 in (the actual dimensions are ½ in smaller) southern pine rafters is 53 pcf. The 2" insulation weighs 3 psf, and the asphalt roofing weighs 5.5 psf.arrow_forwardA cylindrical wood covered with steel is the cross-section of the post of a signage as shown. The steel signage has a thickness of 20 mm with a 1.5 m width by 1 m height dimensions and has a density of 7500 kg/m. During storm, the wind strike the signage a pressure of 0.9 kPa. Neglecting the weight of the post and the stress from the torsional moment, find the following; Esee 200 GPa, Eod 10 Gna. Outside diameter of the post is 100 mm, inside diameter is 80 mm. a. The Ia of the transformed section with wood as base material. b. State of stress at point A. Principal stresses and maximum in plane shear stress of "C". d. The transformed stresses of "C" at 20° clockwise.arrow_forwardPLEASE ANSWER ASAP STRUCTURAL THEORYarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Architectural Drafting and Design (MindTap Course...Civil EngineeringISBN:9781285165738Author:Alan Jefferis, David A. Madsen, David P. MadsenPublisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning
Architectural Drafting and Design (MindTap Course...
Civil Engineering
ISBN:9781285165738
Author:Alan Jefferis, David A. Madsen, David P. Madsen
Publisher:Cengage Learning