Concept explainers
(a)
Interpretation:
Formula of calcium phosphate has to be given and also it has to be indicated as ionic or molecular compound.
Concept Introduction:
Naming of ionic compounds that contain monoatomic ions are given by using the name of the cation (mostly metal), which is followed by the name of anion. The anion (mostly nonmetal) is named by adding the suffix “-ide”. When an ionic compound is made up of only two elements, it is known as binary compounds. In case of binary compounds, the numerical prefixes are not shown in the name because the number of ions is inferred from the empirical formula.
In order to obtain the formula from the given name, the cation and anion are identified first. Then the symbol of the cations and anions are written using the charge. Number of subscripts are added either to cation or anion in order to balance the charge.
(b)
Interpretation:
Formula of germanium dioxide has to be written and also it has to be indicated as ionic or molecular compound.
Concept Introduction:
Two or more nonmetals combine to form molecular compounds. The naming of molecular compound is given by following two rules.
- Element that is present in far left of the periodic table appears in the name first.
- Element that is closer to bottom within any of the group appears in the name first.
Numerical prefixes are used in case of molecular compounds to mention how many times the atom of same elements occurs in the formula. Prefix mono is not used for the first element while for the second element it is used.
From the name of molecular compound, the molecular formula can be obtained by considering the name of the first element and second element along with the prefix. The prefix represents the number of atoms of same element is present in the molecular formula. This prefix is entered in subscript in molecular formula after the
(c)
Interpretation:
Formula of iron(III) sulfate has to be given and also it has to be indicated as ionic or molecular compound.
Concept Introduction:
Refer part (a).
(d)
Interpretation:
Formula of phosphorus tribromide has to be written and also it has to be indicated as ionic or molecular compound.
Concept Introduction:
Refer part (b).
Want to see the full answer?
Check out a sample textbook solutionChapter 2 Solutions
Chemistry Principles And Practice
- Don't used hand raitingarrow_forwardCHEM2323 Problem 2-24 Tt O e: ל Predict the product(s) of the following acid/base reactions. Draw curved arrows to show the formation and breaking of bonds. If the bonds needed are not drawn out, you should redraw them. + BF3 (a) (b) HI + (c) OH -BF Problem 2-25 Use curved arrows and a proton (H+) to draw the protonated form of the following Lewis bases. Before starting, add all missing lone pairs. (a) (b) :0: (c) N 1 CHEM2323 PS CH02 Name:arrow_forwardCHEM2323 Problem 2-26 Tt O PS CH02 Name: Use the curved-arrow formalism to show how the electrons flow in the resonance form on the left to give the one on the right. (Draw all lone pairs first) (a) NH2 NH2 + (b) Problem 2-27 Double bonds can also act like Lewis bases, sharing their electrons with Lewis acids. Use curved arrows to show how each of the following double bonds will react with H-Cl and draw the resulting carbocation. (a) H2C=CH2 (b) (c) Problem 2-28 Identify the most electronegative element in each of the following molecules: (a) CH2FCI F Problem 2-29 (b) FCH2CH2CH2Br (c) HOCH2CH2NH2 (d) CH3OCH2Li F 0 0 Use the electronegativity table in Figure 2.3 to predict which bond in the following pairs is more polar and indicate the direction of bond polarity for each compound. (a) H3C-Cl or Cl-CI (b) H3C-H or H-CI (c) HO-CH3 or (CH3)3Si-CH3 (d) H3C-Li or Li-OHarrow_forward
- Reagan is doing an atomic absorption experiment that requires a set of zinc standards in the 0.4-1.6 ppm range. A 1000 ppm Zn solution was prepared by dissolving the necessary amount of solid Zn(NO3)2 in water. The standards can be prepared by diluting the 1000 ppm Zn solution. Table 1 shows one possible set of serial dilutions (stepwise dilution of a solution) that Reagan could perform to make the necessary standards. Solution A was prepared by diluting 5.00 ml of the 1000 ppm Zn standard to 50.00 ml. Solutions C-E are called "calibration standards" because they will be used to calibrate the atomic absorption spectrometer. a. Compare the solution concentrations expressed as ppm Zn and ppm Zn(NO3)2. Compare the concentrations expressed as M Zn and M Zn(NO3)2 - Which units allow easy conversion between chemical species (e.g. Zn and Zn(NO3)2)? - Which units express concentrations in numbers with easily expressed magnitudes? - Suppose you have an analyte for which you don't know the molar…arrow_forwardNonearrow_forwardHow will you prepare the following buffers? 2.5 L of 1.5M buffer, pH = 10.5 from NH4Cl and NH3arrow_forward
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill EducationPrinciples of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
- Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill EducationChemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage LearningElementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY