MATERIALS SCIENCE+ENGINEERING-EPUB CARD
MATERIALS SCIENCE+ENGINEERING-EPUB CARD
10th Edition
ISBN: 9781119405474
Author: Callister
Publisher: WILEY
Question
Book Icon
Chapter 2, Problem 1QAP
To determine

The difference between atomic mass and atomic weight

Expert Solution & Answer
Check Mark

Explanation of Solution

Write the difference between atomic mass and atomic weight in tabular form.

S. no Atomic mass Atomic weight
1 It is defined as adding the number of protons and neutrons in atom. It is defined as average weight of an element, with respect to all isotopes and their abundance.
2 One atomic mass unit (amu) is the one twelfth of the mass of the C-12 isotope. Ratio of the average mass per atom of the element to 1/12 of the mass of atom of C-12.
3

Expression of atomic mass.

AZ+N

Here, A is for atomic mass, Z is for atomic number and N is for neutrons.

Expression for atomic weight of element.

A¯M=ΣifiMAiM

Here, M is for an element, A¯M is for fraction-of-occurrence-atomic weight, AiM is for atomic weight of the isotope, fiM is for fraction-of-occurrence of isotope (i) for element.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
01:18
Students have asked these similar questions
The thin-walled open cross section shown is transmitting torque 7. The angle of twist ₁ per unit length of each leg can be determined separately using the equation 01 = 3Ti GLIC 3 where G is the shear modulus, ₁ is the angle of twist per unit length, T is torque, and L is the length of the median line. In this case, i = 1, 2, 3, and T; represents the torque in leg i. Assuming that the angle of twist per unit length for each leg is the same, show that T= Lic³ and Tmaz = G01 Cmax Consider a steel section with Tallow = 12.40 kpsi. C1 2 mm L1 20 mm C2 3 mm L2 30 mm C3 2 mm L3 25 mm Determine the torque transmitted by each leg and the torque transmitted by the entire section. The torque transmitted by the first leg is | N-m. The torque transmitted by the second leg is N-m. The torque transmitted by the third leg is N-m. The torque transmitted by the entire section is N-m.
Consider a new 1800 MW power plant that burns dry sub-bituminous coal in a PC-wall-fired, wet bottom furnace with plant efficiency of 39%. Use the emission factors in your lecture notes to determine the emission rates of all particulates, PM10, SOx, NOx and CO in ton per year. No gas treatment equipment was installed.
A lignite-fired power plant was designed to produce electricity at a maximum capacity of 750 MW. By average over a year, the plant is operated at 35% plant efficiency and 65% of the design capacity. Assume that the entire amount of sulfur in lignite coal entering the plant is converted to sulfur dioxide (SO2). The power plant is equipped with an 85% efficiency SO2 removal unit. Use the engineering calculation approach and the coal information (dry basis) found in your lecture notes to determine emission rate of SO2 in lb/hr and in lb/BTU input.
Knowledge Booster
Background pattern image
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
MATLAB: An Introduction with Applications
Engineering
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Text book image
Essentials Of Materials Science And Engineering
Engineering
ISBN:9781337385497
Author:WRIGHT, Wendelin J.
Publisher:Cengage,
Text book image
Industrial Motor Control
Engineering
ISBN:9781133691808
Author:Stephen Herman
Publisher:Cengage Learning
Text book image
Basics Of Engineering Economy
Engineering
ISBN:9780073376356
Author:Leland Blank, Anthony Tarquin
Publisher:MCGRAW-HILL HIGHER EDUCATION
Text book image
Structural Steel Design (6th Edition)
Engineering
ISBN:9780134589657
Author:Jack C. McCormac, Stephen F. Csernak
Publisher:PEARSON
Text book image
Fundamentals of Materials Science and Engineering...
Engineering
ISBN:9781119175483
Author:William D. Callister Jr., David G. Rethwisch
Publisher:WILEY