EBK ELECTRICAL WIRING RESIDENTIAL
19th Edition
ISBN: 9781337516549
Author: Simmons
Publisher: CENGAGE LEARNING - CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 19.1, Problem 11R
Why is a 240-volt motor preferable to a 120-volt motor for use in this residence?
______________________________________________________________________
______________________________________________________________________
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Give the number of times the four‑step sequence must be applied to a stepper motor to make a 100‑degree move if the motor has a 5‑degree step angle. Also, fill in the characteristics for your motor below.
Step angle ____________________
Steps per revolution ___________________
Number of rotor teeth __________________
Follow the procedures in troubleshooting the defects and faults of an electric fan by filling in the missing steps.Doesn't rotate 1.___________ 2.____________ Check for Open AC cord or wiring3. ___________4.___________ Defective switch/electronic system control 5. _____________Defective module (system control).
A Single Phase Motor is connected to a 120 Volt, 60 Hz line. The motor has a current draw of 15.7 amperes. A watt meter indicates the motor is actually using 1.340 watts. Find the following:
Apparent power: ___________________________________________________________________________________________
Power factor of the motor; _________________________________________________________________________________
Reactive power of the motor: ________________________________________________________________________________
Capacitance needed to correct the power factor to 100%: ____________________________________________________
Capacitance needed to correct the power factor to 95%: _____________________________________________________
Chapter 19 Solutions
EBK ELECTRICAL WIRING RESIDENTIAL
Ch. 19.1 - Does a jet pump have any electrical moving parts...Ch. 19.1 - Prob. 2RCh. 19.1 - Where is the jet of the pump located?...Ch. 19.1 - Prob. 4RCh. 19.1 - Prob. 5RCh. 19.1 - Prob. 6RCh. 19.1 - Prob. 7RCh. 19.1 - What is compressed in the water storage tank?...Ch. 19.1 - Explain the difference between a 2-wire...Ch. 19.1 - Prob. 10R
Ch. 19.1 - Why is a 240-volt motor preferable to a 120-volt...Ch. 19.1 - How many amperes does a 1-horsepower, 240-volt,...Ch. 19.1 - What size are the conductors used for this branch...Ch. 19.1 - Prob. 14RCh. 19.1 - What provides the running overload protection for...Ch. 19.1 - What is the maximum ampere setting permitted for...Ch. 19.1 - Prob. 17RCh. 19.1 - Because the controller contains the motor starting...Ch. 19.1 - Prob. 19RCh. 19.1 - Proper pressure of the submersible pump system is...Ch. 19.1 - Fill in the data for a 16-ampere electric motor,...Ch. 19.1 - The NEC is very specific in its requirement that...Ch. 19.1 - Does the NEC allow submersible pump cable to be...Ch. 19.1 - Must the disconnect switch for a submersible pump...Ch. 19.1 - A metal well casing (shall) (shall not) be bonded...Ch. 19.2 - Prob. 1RCh. 19.2 - A major hazard involved with water heaters is that...Ch. 19.2 - Prob. 3RCh. 19.2 - The heating elements in electric water heaters are...Ch. 19.2 - An 80-gallon electric water heater is energized...Ch. 19.2 - Prob. 6RCh. 19.2 - For residential water heaters, the Consumer...Ch. 19.2 - An 80-gallon electric water heater has 60F...Ch. 19.2 - Approximately how long would it take to produce...Ch. 19.2 - Two thermostats are generally used in an electric...Ch. 19.2 - a. How many heating elements are provided in the...Ch. 19.2 - When does the lower heating element operate?...Ch. 19.2 - Prob. 14RCh. 19.2 - Prob. 15RCh. 19.2 - Prob. 16RCh. 19.2 - a. If both elements of the water heater in this...Ch. 19.2 - a. How much power in watts would the two elements...Ch. 19.2 - A condominium owner complains of not getting...Ch. 19.2 - For a single, nonmotor-operated electrical...Ch. 19.2 - A 7000-watt resistance-type heating appliance is...Ch. 19.2 - Prob. 22R
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of these places has the highest voltage in a properly working truck electrical system with the engine running and the batteries charging? A. Across battery terminals B. Across cranking motor B+ and cranking motor ground C. Across the alternator plus output stud and alternator ground stud cranking motor ground D. All of the above would be the exact same voltagearrow_forwardFollow the instructions. Existing answers are not enough. Thank youarrow_forwardPlease answer all subpart Thanks sirarrow_forward
- 14: In a natural circulation solar water heater, collector has a glass cover on the top and an ________________ material at the bottom. a. Insulating b. Sheets c. Steel d. Tubes 15: text ____________ wind mill consists of narrow rims and wire spokes. a. Single bladed b. Vertical Axis c. Double bladed d. Multibladedarrow_forwardGenerators can be connected to the electrical system of the residence in several ways (Select all answers that apply) Group of answer choices A. permanent generator where the neutral is not switched by the transfer switch B. portable generator that has the neutral bonded to the frame and is connected to the dwelling electrical system transfer equipment by a flexible cord C. permanent generator where the neutral is switched by the transfer switch D. portable generator that has the neutral isolated or floated from the frame and is connected to the dwelling electrical system transfer equipment by a flexible cordarrow_forwardDo as per instructions and existing answers are not enougharrow_forward
- Part 2: Analysis and selection of the Wind Turbine.The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. What are the two closed loop control systems that are used generally in wind turbines? How do they work? 2. Calculate the power density of the input power from the wind when the wind is blowing at the rated wind speed at the turbine height. Clearly show your steps in details.arrow_forwardgrounded electrodes that are driven rods require a minimum of _____ contact with the soil.arrow_forwardPlease box the final answers... Thankssssarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- EBK ELECTRICAL WIRING RESIDENTIALElectrical EngineeringISBN:9781337516549Author:SimmonsPublisher:CENGAGE LEARNING - CONSIGNMENT
EBK ELECTRICAL WIRING RESIDENTIAL
Electrical Engineering
ISBN:9781337516549
Author:Simmons
Publisher:CENGAGE LEARNING - CONSIGNMENT
How do Universal Motors work ?; Author: Lesics;https://www.youtube.com/watch?v=0PDRJKz-mqE;License: Standard Youtube License