FUND OF ENGINEERING THERMO W/WILEY PLU
8th Edition
ISBN: 9781119391630
Author: MORAN
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 1.9, Problem 32CU
To determine
Whether the statement is true or false “The value of the temperature expressed using the celsius temperature scale is always higher than its value expressed using the Kelvin scale”.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
As shown in the figure below, moist air at T₁ = 36°C, 1 bar, and 35% relative humidity enters a heat exchanger operating at steady state
with a volumetric flow rate of 10 m³/min and is cooled at constant pressure to 22°C. Ignoring kinetic and potential energy effects,
determine:
(a) the dew point temperature at the inlet, in °C.
(b) the mass flow rate of moist air at the exit, in kg/min.
(c) the relative humidity at the exit.
(d) the rate of heat transfer from the moist air stream, in kW.
(AV)1, T1
P₁ = 1 bar
11
= 35%
120
T₂=22°C
P2 = 1 bar
Air at T₁-24°C, p₁-1 bar, 50% relative humidity enters an insulated chamber operating at steady state with a mass flow rate of 3
kg/min and mixes with a saturated moist air stream entering at T₂-7°C, p2-1 bar. A single mixed stream exits at T3-17°C, p3-1 bar.
Neglect kinetic and potential energy effects
Step 1
Your answer is correct.
Determine mass flow rate of the moist air entering at state 2, in kg/min.
m2 = 2.1
Hint
kg/min
Using multiple attempts will impact your score.
5% score reduction after attempt 2
Step 2
Determine the relative humidity of the exiting stream.
Փ3 =
i
%
Attempts: 1 of 3 used
A reservoir at 300 ft elevation has a 6-in.-diameter discharge pipe located 50 ft below the surface. The pipe is 600 ft long and drops in elevation to 150 ft where the flow discharges to the atmosphere. The pipe is made of riveted steel with a roughness height of 0.005 ft.
Determine the flow rate without a head loss
Determine the flow rate with the pipe friction head loss.
(hints: Since the velocity is not known for part b and the Reynolds number and friction factor depend on velocity, you will need to iterate to find the solution. A good first guess is the velocity from part (a))
Chapter 1 Solutions
FUND OF ENGINEERING THERMO W/WILEY PLU
Ch. 1.9 - Prob. 1ECh. 1.9 - Prob. 2ECh. 1.9 - 3. The driver’s compartment of race cars can reach...Ch. 1.9 - 4. What causes changes in atmospheric pressure?
Ch. 1.9 - 5. Why are passenger airplane cabins normally...Ch. 1.9 - 6. Laura takes an elevator from the tenth floor of...Ch. 1.9 - 7. How do dermatologists remove precancerous skin...Ch. 1.9 - 8. When one walks barefoot from a carpet onto a...Ch. 1.9 - 9. Why does ocean water temperature vary with...Ch. 1.9 - 10. Are the systolic and diastolic pressures...
Ch. 1.9 - 11. How do forehead temperature strips work?
Ch. 1.9 - 12. How does a pressure measurement of 14.7 psig...Ch. 1.9 - 13. What is a nanotubel
Ch. 1.9 - 14. If a system is at steady state, does this mean...Ch. 1.9 - For problems 1-10, match the appropriate...Ch. 1.9 - Prob. 11CUCh. 1.9 - 12. Describe the difference between specific...Ch. 1.9 - 13. A system is said to be at ___________ if none...Ch. 1.9 - 14. A control volume is a system that
(a) always...Ch. 1.9 - 15. What is the objective of an engineering model...Ch. 1.9 - 16. _______________ is pressure with respect to...Ch. 1.9 - 17. A gas contained within a piston–cylinder...Ch. 1.9 - 18. The statement, “When two objects are in...Ch. 1.9 - 19. SI base units include
(a) kilogram (kg), meter...Ch. 1.9 - 20. Explain why the value for gage pressure is...Ch. 1.9 - 21. A system is at steady state if
(a) none of its...Ch. 1.9 - Prob. 22CUCh. 1.9 - 23. Classify items a through g shown on the...Ch. 1.9 - 24. When a system is isolated,
(a) its mass...Ch. 1.9 - 25. The resultant pressure force acting on a body...Ch. 1.9 - 26. The list consisting only of intensive...Ch. 1.9 - 27. Gage pressure indicates the difference between...Ch. 1.9 - 28. Systems can be studied only from a macroscopic...Ch. 1.9 - 29. Kilogram, second, foot, and newton are all...Ch. 1.9 - Prob. 30CUCh. 1.9 - 31. Mass is an intensive property.
Ch. 1.9 - Prob. 32CUCh. 1.9 - 33. Intensive properties may be functions of both...Ch. 1.9 - 34. Devices that measure pressure include...Ch. 1.9 - Prob. 35CUCh. 1.9 - 36. If a system is isolated from its surroundings...Ch. 1.9 - 37. The specific volume is the reciprocal of the...Ch. 1.9 -
Indicate whether the following statements are...Ch. 1.9 - 39. The pound force, lbf, is equal to the pound...Ch. 1.9 - 40. The value of a temperature expressed using the...Ch. 1.9 - Prob. 41CUCh. 1.9 - 42. A closed system always contains the same...Ch. 1.9 - Prob. 43CUCh. 1.9 - 44. A control volume is a special type of closed...Ch. 1.9 - 45. When a closed system undergoes a process...Ch. 1.9 - Prob. 46CUCh. 1.9 - Prob. 47CUCh. 1.9 - 48. A vessel holding 0.5 kg of oxygen (O2)...Ch. 1.9 - Prob. 49CUCh. 1.9 - 50. In local surroundings at standard atmospheric...Ch. 1.9 - Prob. 51CUCh. 1.9 - 52. The Rankine degree is a smaller temperature...Ch. 1.9 - 53. If the value of any property of a system...Ch. 1.9 - Prob. 54CUCh. 1.9 - 55. The composition of a closed system cannot...Ch. 1.9 - 56. Temperature is the property that is the same...Ch. 1.9 - Prob. 57CUCh. 1.9 - 58. The pressure unit psia indicates an absolute...Ch. 1.9 - 1.4 Perform the following unit conversions:
(a) 1...Ch. 1.9 - 1.5 Perform the following unit conversions:
(a)...Ch. 1.9 - 1.6 Which of the following food items weighs...Ch. 1.9 - 1.7 A person whose mass is 150 lb weighs 144.4...Ch. 1.9 - 1.8 The Phoenix with a mass of 350 kg was a...Ch. 1.9 - Prob. 9PCh. 1.9 - 1.10 In severe head-on automobile accidents, a...Ch. 1.9 - Prob. 11PCh. 1.9 - 1.12 A spring compresses in length by 0.14 in, for...Ch. 1.9 - 1.13 At a certain elevation, the pilot of a...Ch. 1.9 - 1.14 Estimate the magnitude of the force, in Ibf,...Ch. 1.9 - 1.15 Determine the upward applied force, in Ibf,...Ch. 1.9 -
1.16 An object is subjected to an applied upward...Ch. 1.9 - 1.17 A communications satellite weighs 4400 N on...Ch. 1.9 - 1.18 Using local acceleration of gravity data from...Ch. 1.9 - 1.19 A town has a 1-million-gallon storage...Ch. 1.9 - 1.20 A closed system consists of 0.5 kmol of...Ch. 1.9 - 1.21 A 2-lb sample of an unknown liquid occupies a...Ch. 1.9 - Prob. 22PCh. 1.9 - 1.23 The specific volume of 5 kg of water vapor at...Ch. 1.9 - Prob. 24PCh. 1.9 - 1.25 As shown in Figure P1.25, a gas is contained...Ch. 1.9 - 1.26 As shown in Fig. P1.26, a vertical...Ch. 1.9 - 1.27 Three kg of gas in a piston-cylinder assembly...Ch. 1.9 - 1.28 A closed system consisting of 4 lb of a gas...Ch. 1.9 - 1.29 A system consists of carbon monoxide (CO) in...Ch. 1.9 - 1.30 Figure P1.30 shows a gas contained in a...Ch. 1.9 - 1.31 A gas contained within a piston-cylinder...Ch. 1.9 - Prob. 32PCh. 1.9 - 1.33 Figure P 1.33 shows a storage tank holding...Ch. 1.9 - 1.34 As shown in Figure PI.34, the exit of a gas...Ch. 1.9 - 1.35 The barometer shown in Fig. P1.35 contains...Ch. 1.9 - Prob. 36PCh. 1.9 - Figure P1.37 shows a tank within a tank, each...Ch. 1.9 - 1.38 As shown in Fig. PI.38, an underwater...Ch. 1.9 - 1.39 Show that a standard atmospheric pressure of...Ch. 1.9 - 1.40 A gas enters a compressor that provides a...Ch. 1.9 - 1.41 As shown in Figure P1.41. air is contained in...Ch. 1.9 - Prob. 42PCh. 1.9 - 1.43 The pressure from water mains located at...Ch. 1.9 - 1.44 Figure P1.44 shows a tank used to collect...Ch. 1.9 - 1.45 If the water pressure at the base of the...Ch. 1.9 - 1.46 As shown in Figure P1.46. an inclined...Ch. 1.9 - 1.47 Figure P1.47 shows a spherical buoy, having a...Ch. 1.9 - 1.48 Because of a break in a buried oil storage...Ch. 1.9 - 1.49 Figure P1.49 shows a closed tank holding air...Ch. 1.9 - 1.50 The 30-year average temperature in Toronto,...Ch. 1.9 - 1.51 Convert the following temperatures from °F to...Ch. 1.9 - Prob. 52PCh. 1.9 - 1.53 A cake recipe specifies an oven temperature...Ch. 1.9 - 1.54 Does the Rankine degree represent a larger or...Ch. 1.9 - 1.55 Figure P1.55 shows a system consisting of a...Ch. 1.9 - What is (a) the lowest naturally occurring...Ch. 1.9 - 1.57 Air temperature rises from a morning low of...Ch. 1.9 - 1.58 For liquid-in-glass thermometers, the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Air at T₁-24°C, p₁-1 bar, 50% relative humidity enters an insulated chamber operating at steady state with a mass flow rate of 3 kg/min and mixes with a saturated moist air stream entering at T₂-7°C, p2-1 bar. A single mixed stream exits at T3-17°C, p3-1 bar. Neglect kinetic and potential energy effects Step 1 Your answer is correct. Determine mass flow rate of the moist air entering at state 2, in kg/min. m2 = 2.1 Hint kg/min Using multiple attempts will impact your score. 5% score reduction after attempt 2 Step 2 Determine the relative humidity of the exiting stream. Փ3 = i % Attempts: 1 of 3 usedarrow_forward25 mm Brass core E = 105 GPa 0 = 20.9 x 10 °C PROBLEM 2.49 The aluminum shell is fully bonded to the brass core and the assembly is unstressed at a temperature of 15°C. Considering only axial deformations, determine the stress in the aluminum when the temperature reaches 195°C. 60 mm Aluminum shell E = 70 GPa a = 23.6 × 10°Carrow_forwardThis is an old practice exam. The answers are OAB = 19.10 ksi OBC = 2.228 ksi OCD = −2.865 ksi v = 0.2792delta Ltot = 0.01585 in (increase) but whyarrow_forward
- A random poly(styrene-butadiene) copoly- mer has a number-average molecular weight of 350,000 g/mol and a degree of polymerization of 5000. Compute the fraction of styrene and buta- diene repeat units in this copolymer. H H | | -C-C- 방 Harrow_forwardDesign and assemble on the fluidsim (or a draft) the Hydraulic Drive Circuit, with the following characteristics: (a) Sequential operation, pressure, for the advance and return of the cylinders (according to the proper operation for the device) controlled by a directional 4x3 way, closed center; (b) Speed control for the cylinders, according to the load signal; (c) Pressure counterbalance for cylinder A, in order to compensate for the weight of the assembly.arrow_forwardThis is an old exam practice question. The answer is Pmax = 218.8 kN normal stress governs but why?arrow_forward
- Moist air initially at T₁ = 140°C, p₁ = 4 bar, and p₁ = 50% is contained in a 2.0-m³ closed, rigid tank. The tank contents are cooled to T₂ 35°C. Step 1 Determine the temperature at which condensation begins, in °C.arrow_forwardAir at T₁ = 24°C, p₁ = 1 bar, 50% relative humidity enters an insulated chamber operating at steady state with a mass flow rate of 3 kg/min and mixes with a saturated moist air stream entering at T2=7°C, p₂ = 1 bar. A single mixed stream exits at T3-17°C, p3=1 bar. Neglect kinetic and potential energy effectsarrow_forwardHand calculation of cooling loadarrow_forward
- An HEV has a 24kW battery. How many miles can it go on electricity alone at 40 mph on a flat straight road with no headwind? Assume the rolling resistance factor is 0.018 and the Coefficient of Drag (aerodynamic) is 0.29 the frontal area is 2.25m^2 and the vehicle weighs 1618 kg.arrow_forwardAs shown in the figure below, moist air at T₁ = 36°C, 1 bar, and 35% relative humidity enters a heat exchanger operating at steady state with a volumetric flow rate of 10 m³/min and is cooled at constant pressure to 22°C. Ignoring kinetic and potential energy effects, determine: (a) the dew point temperature at the inlet, in °C. (b) the mass flow rate of moist air at the exit, in kg/min. (c) the relative humidity at the exit. (d) the rate of heat transfer from the moist air stream, in kW. (AV)1, T1 P₁ = 1 bar 11 = 35% 120 T₂=22°C P2 = 1 bararrow_forwardThe inside temperature of a wall in a dwelling is 19°C. If the air in the room is at 21°C, what is the maximum relative humidity, in percent, the air can have before condensation occurs on the wall?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Thermodynamics - Chapter 3 - Pure substances; Author: Engineering Deciphered;https://www.youtube.com/watch?v=bTMQtj13yu8;License: Standard YouTube License, CC-BY