An air pump has a cylinder 0.250 m long with a movable piston. The pump is used to compress air from the atmosphere (at absolute pressure 1.01 × 105 Pa) into a very large tank at 3.80 × 105 Pa gauge pressure. (For air, Cv = 20.8 J/mol · K.) (a) The piston begins the compression stroke at the open end of the cylinder. How far down the length of the cylinder has the piston moved when air first begins to flow from the cylinder into the tank? Assume that the compression is adiabatic. (b) If the air is taken into the pump at 27.0°C, what is the temperature of the compressed air? (c) How much work does the pump do in putting 20.0 mol of air into the tank?
Want to see the full answer?
Check out a sample textbook solutionChapter 19 Solutions
University Physics (14th Edition)
Additional Science Textbook Solutions
Introduction to Electrodynamics
An Introduction to Thermal Physics
Life in the Universe (4th Edition)
Sears And Zemansky's University Physics With Modern Physics
Physics (5th Edition)
Cosmic Perspective Fundamentals
- If a gas is compressed isothermally, which of the following statements is true? (a) Energy is transferred into the gas by heat. (b) No work is done on the gas. (c) The temperature of the gas increases. (d) The internal energy of the gas remains constant. (e) None of those statements is true.arrow_forwardA vertical cylinder of cross-sectional area A is fitted with a tight-fitting, frictionless piston of mass m (Fig. P18.40). The piston is not restricted in its motion in any way and is supported by the gas at pressure P below it. Atmospheric pressure is P0. We wish to find the height h in Figure P18.40. (a) What analysis model is appropriate to describe the piston? (b) Write an appropriate force equation for the piston from this analysis model in terms of P, P0, m, A, and g. (c) Suppose n moles of an ideal gas are in the cylinder at a temperature of T. Substitute for P in your answer to part (b) to find the height h of the piston above the bottom of the cylinder. Figure P18.40arrow_forwardA hand-driven tire pump has a piston with a 2.50-cm diameter and a maximum stroke of 30.0 cm. (a) How much work do you do in one stroke if the average gauge pressure is 2.1105 N/m2 (about 35 psi)? (b) What average force do you exert on the piston, neglecting friction and gravitational force?arrow_forward
- A car engine moves a piston with a circular cross-section of 73000.002cm in diameter a distance of 3.2500.001cm to compress the gas in the cylinder. (a) By what amount is the gas decreased in volume in cubic centimeters? (b) Find the uncertainty in this volume.arrow_forwardGas in a container is at a pressure of 1.2 atm and a volume of 7.0 m3. (a) What is the work done on the gas if it expands at constant pressure to twice its initial volume? (b) What is the work done on the gas if it is compressed at constant pressure to one-quarter of its initial volume?arrow_forwardA hand-driven tire pump has a piston with a 2.00 cm diameter and a maximum stroke of 29.0 cm. (a) How much work (in J) do you do in one stroke if the average gauge pressure is 2.40 ✕ 105 N/m2 (about 35 psi)? (b)What average force (in N) do you exert on the piston, neglecting friction and gravity?arrow_forward
- A vertical cylindrical tank contains 1.80 mol of an ideal gas tinder a pressure of 0.300 atm at 20.0°C. The round part of the tank has a radius of 10.0 cm, and the gas is supporting a piston that can move up and down in the cylinder without friction. There is a vacuum above the piston. What is the mass of this piston?arrow_forwardThe plunger of a syringe has an internal diameter of 1.0 cm and the end of the needle has an internal diameter of 0.35 mm. A practitioner lightly squeezes the plunger, but no serum is emitted by the needle into a vein. So the practitioner gradually increases the squeezing force that she exerts on the plunger such that serum begins to be emitted from the needle into the vein. Assuming no surface tension or friction, what is the minimum squeezing force that the practitioner applies to the plunger in order that serum begins to be emitted from the needle into the vein? Take the pressure of blood in the vein to be 20 mmHg above that of atmospheric pressure. 0.70 N 3.3 N 0.21 N 0.24 N 1.4 N 17Narrow_forwardThe plunger of a syringe has an internal diameter of 1.0 cm and the end of the needle has an internal diameter of 0.35 mm. A practitioner lightly squeezes the plunger, but no serum is emitted by the needle into a vein. So the practitioner gradually increases the squeezing force that she exerts on the plunger such that serum begins to be emitted from the needle into the vein. Assuming no surface tension or friction, what is the minimum squeezing force that the practitioner appli to the plunger in order that serum begins to be emitted from the needle into the vein? Take the pressure of blood in the vein to be 20 mmHg above that of atmospheric pressure. 0.70 N 1.4 N 3.3 N 1.7 N 0.21 N 0.24 Narrow_forward
- Gas in a container is at a pressure of 1.8 atm and a volume of 6.0 m³. (a) What is the work done on the gas if it expands at constant pressure to twice its initial volume? X Use the expression relating the pressure and change in volume to the work done. J (b) What is the work done on the gas if it is compressed at constant pressure to one-quarter of its initial volume?arrow_forwardFour ideal gases have the following pressures, P, volumes, V,and mole numbers, n: gas A, P = 100 kPa, V = 1 m3, n = 10 mol;gas B, P = 200 kPa, V = 2 m3, n = 20 mol; gas C, P = 50 kPa,V = 1 m3, n = 50 mol; gas D, P = 50 kPa, V = 4 m3, n = 5 mol.Rank these gases in order of increasing temperature. Indicate tieswhere appropriate.arrow_forwardWhen a .22-caliber rifle is fired, the expanding gas from the burning gunpowder creates a pressure behind the bullet. This pressure causes the force that pushes the bullet through the barrel. Suppose the barrel has a length of 0.633 m and an opening whose radius is 2.67 x 10-3 m. A bullet (mass = 2.6 x 10-3 kg) has a speed of 348 m/s after passing through this barrel. Ignore friction and determine the average pressure of the expanding gas.arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University