
(a)
The length of the tube.
(a)

Explanation of Solution
Given:
The mass flow rate
The diameter
The initial temperature
The final temperature
The tube wall temperature
Calculation:
Calculate the bulk mean fluid temperature
Refer table
Obtain the following properties of water corresponding to the temperature of
Calculate the rate of heat transfer
Calculate the velocity of water
Calculate the Reynold number
The Reynolds number is greater than 10000 therefore flow is turbulent flow.
Calculate the Nusselt number
Calculate the heat transfer coefficient
Calculate the logarithmic mean temperature difference
Calculate the surface area
Calculate the length
Thus, the length of the tube is
(b)
The outlet temperature of water.
(b)

Explanation of Solution
Given:
If the tube length is doubled.
Calculation:
Calculate the outlet temperature
Use trial error method to solve the above equation.
Assume
Since, the left hand side and right hand is not equal therefore, this assumption is wrong.
Assume
Since, the left hand side and right hand is not equal therefore, this assumption is wrong.
Assume
Since, the left hand side and right hand is equal therefore, this assumption is correct.
Thus, the outlet temperature of the water is
Want to see more full solutions like this?
Chapter 19 Solutions
Fundamentals of Thermal-Fluid Sciences
- Auto Controls Hand sketch the root Focus of the following transfer function How many asymptotes are there ?what are the angles of the asymptotes?Does the system remain stable for all values of K NO COPIED SOLUTIONSarrow_forward-400" 150" in Datum 80" 90" -280"arrow_forwardUsing hand drawing both of themarrow_forward
- A 10-kg box is pulled along P,Na rough surface by a force P, as shown in thefigure. The pulling force linearly increaseswith time, while the particle is motionless att = 0s untilit reaches a maximum force of100 Nattimet = 4s. If the ground has staticand kinetic friction coefficients of u, = 0.6 andHU, = 0.4 respectively, determine the velocityof the A 1 0 - kg box is pulled along P , N a rough surface by a force P , as shown in the figure. The pulling force linearly increases with time, while the particle is motionless at t = 0 s untilit reaches a maximum force of 1 0 0 Nattimet = 4 s . If the ground has static and kinetic friction coefficients of u , = 0 . 6 and HU , = 0 . 4 respectively, determine the velocity of the particle att = 4 s .arrow_forwardCalculate the speed of the driven member with the following conditions: Diameter of the motor pulley: 4 in Diameter of the driven pulley: 12 in Speed of the motor pulley: 1800 rpmarrow_forward4. In the figure, shaft A made of AISI 1010 hot-rolled steel, is welded to a fixed support and is subjected to loading by equal and opposite Forces F via shaft B. Stress concentration factors K₁ (1.7) and Kts (1.6) are induced by the 3mm fillet. Notch sensitivities are q₁=0.9 and qts=1. The length of shaft A from the fixed support to the connection at shaft B is 1m. The load F cycles from 0.5 to 2kN and a static load P is 100N. For shaft A, find the factor of safety (for infinite life) using the modified Goodman fatigue failure criterion. 3 mm fillet Shaft A 20 mm 25 mm Shaft B 25 mmarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





