Automotive Technology: A Systems Approach - With Manual and Access
6th Edition
ISBN: 9781305513235
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 5ASRQ
Technician A checks a starter’s field coils for opens by connecting an ohmmeter between the coils' power feed wire and the field coil brush lead. Technician B checks a starters field coil for a short to ground by connecting an ohmmeter across the field coil brush lead and the starter housing. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A checks a starter’s field coils for opensby connecting an ohmmeter between the coils’power feed wire and the field coil brush lead. TechnicianB checks a starter’s field coil for a short toground by connecting an ohmmeter across the fieldcoil brush lead and the starter housing. Who iscorrect?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
When the starter spins but does not crank the engine,which of the following may be true?a. Defective starter relayb. Damaged flywheel teethc. A faulty starter solenoidd. All of the above
The required gap in ignition
system between----
-0.4 to 5
O .-4 to 5
0.4 to 0.5
-4 to 0.5
Skip
The suitable thread of spark plug
for heavy engine is
O M18
M19
M15
M16
O Skip
Chapter 18 Solutions
Automotive Technology: A Systems Approach - With Manual and Access
Ch. 18 - True or False? The strength of the magnetic field...Ch. 18 - Prob. 2RQCh. 18 - Prob. 3RQCh. 18 - True or False? Many armature bearings are held in...Ch. 18 - Which of the following is not part of the starter...Ch. 18 - Which of the following tests would not be...Ch. 18 - When the starter spins but does not crank the...Ch. 18 - If the solenoid clicks while trying to crank the...Ch. 18 - Prob. 9RQCh. 18 - Prob. 10RQ
Ch. 18 - Prob. 11RQCh. 18 - The device that prevents the engine from turning...Ch. 18 - The part of the armature that the brushes ride on...Ch. 18 - Describe how to perform a starter bench test.Ch. 18 - A control circuit voltage drop test shows a 1.1...Ch. 18 - An engine cranks slowly: Technician A says that a...Ch. 18 - While discussing armature testing: Technician A...Ch. 18 - Pinion gear-to-flywheel ring gear clearance is...Ch. 18 - Technician A says that a starter no-load test is...Ch. 18 - Technician A checks a starters field coils for...Ch. 18 - Prob. 6ASRQCh. 18 - When diagnosing a no-crank no-start condition, no...Ch. 18 - While discussing a no-crank condition: Technician...Ch. 18 - Prob. 9ASRQCh. 18 - While discussing electric motors: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing a no-crank condition: Technician A says to verify the condition of the batten' before testing the starter motor Technician B says a scan tool may be used to check starter control circuit operation. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that a starter no-load test is conducted with the starter in a bench vise. Technician B says that the no-load test is used to determine starter motor circuit voltage drop. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen diagnosing a no-crank no-start condition, no voltage is present at the S terminal of the solenoid while attempting to crank the engine. Technician A says a faulty starter motor is the cause. Technician B says a shorted safety switch is the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Cranking current is excessive but is normal when the starter is bench tested: Technician A says the problem could be with the positive battery connection to the solenoid. Technician B says there could be an engine mechanical problem. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhen the starter spins but does not crank the engine, which of the following may be true? Defective starter relay Damaged flywheel teeth A faulty starter solenoid All of the abovearrow_forwardIf the solenoid clicks while trying to crank the engine with the starter, which of the following is not a probable cause? A faulty neutral safety switch Low battery voltage Low voltage available to the solenoid An open in the hold-in windingarrow_forward
- Describe how to perform a starter bench test.arrow_forwardTechnician A says the switching device controls the flow of current through the coil primary winding. Technician B says that when the switching device stops supplying current to the coil primary winding, it is time to fire the spark plug. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile inspecting the synchronizers of a transaxle: Technician A says that if the clutch teeth of the syn chronizer are rounded, the synchronizer assembly must be replaced. Technician B says that the move ment of the synchronizer sleeve on the shaft should be checked. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- A starter cranks, but cranks slowly. The shop performs a voltage drop on the ground and power side of the starter circuit and they both test good. Technician A says the battery may be bad. Technician B says the starter may be bad. Who is correct?arrow_forwardIn El systems using one ignition coil for every two cylinders: Technician A says that two plugs fire at the same time with the same voltage used by each spark plug. Technician B says that one plug fires in the normal direction (center to side electrode) and the other in reversed polarity (side to center). Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile discussing ignition timing requirements: Technician A says that more advanced timing is desired when the engine is under a heavy load. Technician B says that more advanced timing is desired when the engine is running at high engine speeds. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License