
A uniform slender rod of length L is dropped onto rigid supports at A and B. Because support B is slightly lower than support A, the rod strikes A with a velocity
Fig. P17.111
(a)

Find the angular velocity of the rod and the velocity of its mass center immediately after the rod strikes support A.
Answer to Problem 17.111P
The angular velocity of the rod when mass center immediately after the rod strikes support A is
The velocity of the rod when mass center immediately after the rod strikes support A
Explanation of Solution
Given information:
The length of uniform slender rod is L.
The mass of uniform slender rod is m.
The initial velocity of bar before it strikes B is
Calculation:
Write the equation of centroidal moment of inertia
The impact is perfectly elastic at both A and B. Therefore, the coefficient of restitution is one
Write the impact condition for the given system after the rod strikes support A.
Here,
Write the equation of velocity of rod
Here,
Substitute
Consider the impulse and momentum principle.
Sketch the impulse and momentum diagram for the first impact at A of the bar as shown in Figure (1).
Here,
Refer Figure (1).
Take moment about A (positive sign in clockwise direction).
Substitute
Simplify the Equation:
Thus, the angular velocity of the rod and the velocity of its mass center immediately after the rod strikes support A is
Find the velocity of the rod when mass center immediately after the rod strikes support A using Equation (1).
Substitute
Thus, the velocity of the rod when mass center immediately after the rod strikes support A
(b)

Find the angular velocity of the rod and the velocity of its mass center immediately after the rod strikes support B.
Answer to Problem 17.111P
The angular velocity of the rod when mass center immediately after the rod strikes support B is
The velocity of the rod when mass center immediately after the rod strikes support B is
Explanation of Solution
Calculation:
Write the impact condition for the given system after the rod strikes support B.
Here,
Write the equation of velocity of rod
Here,
Substitute
Consider the impulse and momentum principle.
Sketch the impulse and momentum diagram for impact at B of the bar as shown in Figure (2).
Here,
Refer Figure (2).
Take moment about B (positive sign in clockwise direction).
Substitute
Thus, the angular velocity of the rod when mass center immediately after the rod strikes support B is
Find the velocity of the rod when mass center immediately after the rod strikes support B using Equation (2).
Substitute
Thus, the velocity of the rod when mass center immediately after the rod strikes support B
(c)

Find the angular velocity of the rod and the velocity of its mass center immediately after the rod strikes support A again.
Answer to Problem 17.111P
The angular velocity of the rod when mass center immediately after the rod strikes support A again is
The velocity of the rod when mass center immediately after the rod strikes support A again is
Explanation of Solution
Calculation:
Write the impact condition for the given system after the rod again strikes support A.
Here,
Write the equation of velocity of rod
Here,
Substitute
Consider the impulse and momentum principle.
Sketch the impulse and momentum diagram for second impact at A of the bar as shown in Figure (3).
Refer Figure (3).
Take moment about A (positive sign in clockwise direction).
Substitute
Thus, the angular velocity of the uniform slender rod after rod again strikes support A support B is
Find the velocity of rod at its mass center after the rod again strikes support A using Equation (3).
Substitute 0 for
Thus, the velocity of rod at its mass center after the rod again strikes support A is
Want to see more full solutions like this?
Chapter 17 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Mechanics of Materials (10th Edition)
Web Development and Design Foundations with HTML5 (8th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Java: An Introduction to Problem Solving and Programming (8th Edition)
Thermodynamics: An Engineering Approach
Elementary Surveying: An Introduction To Geomatics (15th Edition)
- Qu 3 Nickel (Ni) single crystal turbine blades burn less fuel at higher temperatures because blades are grown on [110] closed packed direction. Nickel (Ni) at 20°C is FCC, and has an atomic radius, R, of 0.125 nm. Draw a reduced-sphere unit cell for this crystal and draw and label the vector [I 10], starting from the origin (0, 0, 0). a) Calculate the length of the vector [| 10] in nanometers. Express your answer in nanometers to one significant figure. b) Calculate the linear density of Nickel in the [| 1 0] direction in [atom/nm]. Express your answer in atoms/nm to one significant figure. show all work problemsarrow_forwardhandwritten-solutions, please!arrow_forwardhandwritten-solutions, please!arrow_forward
- Required information An eccentric force P is applied as shown to a steel bar of 25 × 90-mm cross section. The strains at A and B have been measured and found to be εΑ = +490 μ εB=-70 μ Know that E = 200 GPa. 25 mm 30 mm 90 mm 45 mm B Determine the distance d. The distance dis 15 mm mm.arrow_forwardhandwritten-solutions, please!arrow_forwardhandwritten-solutions, please!arrow_forward
- ! Required information Assume that the couple shown acts in a vertical plane. Take M = 25 kip.in. r = 0.75 in. A B 4.8 in. M 1.2 in. [1.2 in. Determine the stress at point B. The stress at point B is ksi.arrow_forwardhandwritten-solutions, please!arrow_forwardhandwritten-solutions, please!arrow_forward
- No use chatgptarrow_forwardProblem 6 (Optional, extra 6 points) 150 mm 150 mm 120 mm 80 mm 60 mm PROBLEM 18.103 A 2.5 kg homogeneous disk of radius 80 mm rotates with an angular velocity ₁ with respect to arm ABC, which is welded to a shaft DCE rotating as shown at the constant rate w212 rad/s. Friction in the bearing at A causes ₁ to decrease at the rate of 15 rad/s². Determine the dynamic reactions at D and E at a time when ₁ has decreased to 50 rad/s. Answer: 5=-22.01 +26.8} N E=-21.2-5.20Ĵ Narrow_forwardProblem 1. Two uniform rods AB and CE, each of weight 3 lb and length 2 ft, are welded to each other at their midpoints. Knowing that this assembly has an angular velocity of constant magnitude c = 12 rad/s, determine: (1). the magnitude and direction of the angular momentum HD of the assembly about D. (2). the dynamic reactions (ignore mg) at the bearings at A and B. 9 in. 3 in. 03 9 in. 3 in. Answers: HD = 0.162 i +0.184 j slug-ft²/s HG = 2.21 k Ay =-1.1 lb; Az = 0; By = 1.1 lb; B₂ = 0.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





