MATERIALS SCIENCE AND ENGINEERING -PACK
10th Edition
ISBN: 9781119721857
Author: Callister
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Question
Chapter 17, Problem 2DP
(a)
To determine
To suggest:
An appropriate material for the following applications, and, if necessary recommend corrosion prevention measures.
Laboratory bottles to contain relatively dilute solutions of nitric acid.
(b)
To determine
To suggest:
An appropriate material for the following applications, and, if necessary recommend corrosion prevention measures.
Barrels to contain benzene:
(c)
To determine
To suggest:
An appropriate material for the following applications, and, if necessary recommend corrosion prevention measures.
Pipe to transport hot alkaline (basic) solutions:
(d)
To determine
To suggest:
An appropriate material for the following applications, and, if necessary recommend corrosion prevention measures.
Underground tanks to store large quantities of high-purity water:
(e)
To determine
To suggest:
An appropriate material for the following applications, and, if necessary recommend corrosion prevention measures.
Architectural trim for high-rise buildings:
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
3. The shaft below is made of steel (G = 80GPa). It has a diameter of 25mm and is fixed and
supported at the two ends of the shaft, A and D.
(i) Is this a statically indeterminate problem? Why?
(ii) Can you draw the torque load diagram without first resolving the reaction torques at A
or D?
(iii) Determine the reaction torque at A and D.
(iv) Draw the torque load diagram.
(v) Determine the angle of twist at section AB.
B
90 N·m
0.6 m
0.75 m
0.9 m
90 N-m
F3
Ꮎ
N
Ф
F2
F1
There are 3 forces acting on the eye bolt.
Force F1 acts on the XY plane has a magnitude of 536 lbf,
and the angle of 0 = 38°.
Force F2 acts on the YZ plane has a magnitude of 651 lbƒ,
and the angle = 41°.
Force F3 has a magnitude of 256 lb, and coordinate
direction angles of α = 71°, ẞ = 115°, and γ = 33°.
Determine the resultant force on the eye bolt.
FR =
506
☑ i+
+642
713
lbf
FR magnitude: 1084
FR coordinate direction angle a:
Ꭱ
62
× deg
FR coordinate direction angle ẞ`:
49
× deg
FR coordinate direction angle y: 54
deg
x lbf
k)
✓
3
Chapter 17 Solutions
MATERIALS SCIENCE AND ENGINEERING -PACK
Ch. 17 - Prob. 1QAPCh. 17 - Prob. 2QAPCh. 17 - Prob. 3QAPCh. 17 - Prob. 4QAPCh. 17 - Prob. 10QAPCh. 17 - Prob. 13QAPCh. 17 - Prob. 15QAPCh. 17 - Prob. 16QAPCh. 17 - Prob. 19QAPCh. 17 - Prob. 20QAP
Ch. 17 - Prob. 21QAPCh. 17 - Prob. 22QAPCh. 17 - Prob. 23QAPCh. 17 - Prob. 24QAPCh. 17 - Prob. 25QAPCh. 17 - Prob. 26QAPCh. 17 - Prob. 27QAPCh. 17 - Prob. 29QAPCh. 17 - Prob. 31QAPCh. 17 - Prob. 32QAPCh. 17 - Prob. 1DPCh. 17 - Prob. 2DPCh. 17 - Prob. 3DPCh. 17 - Prob. 1FEQPCh. 17 - Prob. 2FEQPCh. 17 - Prob. 3FEQP
Knowledge Booster
Similar questions
- A crate is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the xy plane. Point A is located at a height of h = 121.92 cm above the top of the crate directly over the geometric center of the top surface. Use the given dimensions from the table below to perform the following calculations: a.) Determine the position vector FAD that describes rope AD. b.) Compute the unit vector cд that points from point C to point A. c.) If rope AB carries a tension force of magnitude FT = 760 →> N, determine the force vector FT that expresses how this force acts on point A. Express each vector in Cartesian components to three significant figures. 2013 Michael Swanbom Cc 10 BY NC SA ↑Z b x B A D a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Be sure to align your cartesian unit vectors with the coordinate axes shown in the figure. Variable Value →> a 101.6 cm b 124.46 cm с 38.71 cm a. r AD = b. uca =…arrow_forward3. The shaft below is made of steel (G = 80GPa). It has a diameter of 25mm and is fixed and supported at the two ends of the shaft, A and D. (i) Is this a statically indeterminate problem? Why? (ii) Can you draw the torque load diagram without first resolving the reaction torques at A or D? (iii) Determine the reaction torque at A and D. (iv) Draw the torque load diagram. (v) Determine the angle of twist at section AB. B 90 N·m 0.6 m 0.75 m 0.9 m 90 N-marrow_forward3- A horizontal Venturi meter with d1 = 20 cm, and d₂ = 10 cm, is used to measure the flow rate of oil of sp.gr. 0.8, the discharge through venture meter is 60 lit/s. find the reading of (oil-Hg) differential Take Cd = 0.98.arrow_forward
- 4- A horizontal Venturi meter is used to measure the flow rate of water through the piping system of 20 cm I.D, where the diameter of throat in the meter is d₂ = 10 cm. The pressure at inlet is 17.658 N/cm2 gauge and the vacuum pressure of 35 cm Hg at throat. Find the discharge of water. Take Cd 0.98.arrow_forwardH.W: 1-A Pitot tube is inserted in the pipe of 30 cm I.D. The static pressure head is 10 cm Hg vacuum, and the stagnation pressure at center of the pipe is 0.981 N/cm2 gauge. Calculate the discharge of water through the pipe if u/umax = 0.85. Take Cp = 0.98.arrow_forward2- A Pitot tube is used to measure the air flow rate in a circular duct 60 cm I.D. The flowing air temperature is 65.5°C. The Pitot tube is placed at the center of the duct and the reading R on the manometer is 10.7 mm of water. A static pressure measurement obtained at the Pitot tube position is 205 mm of water above atmospheric. Take Cp = 0.98, = 2.03 x 10-5 Pa.s Calculate the velocity at the center and the average velocity. Calculate the volumetric flow rate of the flowing air in the duct.arrow_forward
- 2. A series of gears are mounted on a 40mm diameter steel shaft. Take G = 75 GPa. (i) Draw the torque load diagram. (ii) Determine the angle of twist of gear B relative to gear A. (iii) Determine the maximum shear stress and it's location along the shaft. 600 N-m 900 N-m 200 mm 200 mm 200 mm 500 Nm 300 N·m 200 mm 500 N-marrow_forward1. The figure below shows a circular shaft with three sections. The length of each section is 50mm. (E 500 MPa). = (i) Draw the axial load diagram of the circular shaft. (ii) Determine the average normal stress at points A, B and C. (iii) Determine the maximum deformation and it's location along the shaft. 10 mm 5 mm 5 mm B 300 N A 900 N 800 N C 200 Narrow_forward4. The following assembly is made of an Aluminium rod (E = 500 MPa). The diameter of the rods is 25mm and 50mm. The ends of the rod are fixed at A and C. A 400 mm 1400 kN B 800 mm (i) Is this a statically indeterminate problem? Why? (ii) Can you draw the axial load diagram without first resolving the reaction forces at A and C? (iii) Determine the reaction forces at A and C. (iv) Draw the axial load diagram. (v) Determine the deformation at section BC.arrow_forward
- A single phase a.c. distributor AB has: The distance from A to B is 500 m. The distance from A to C is 800 m. The impedance of each section is (6+j 8) /km. A B C The voltage at the far end is maintained at 250 volt. Find: sending voltage, sending current, supply power factor and 80 A 60 A total voltage drop. 0.8 lag. P.f 0.6 lead. p.farrow_forwardA 3-phase, 4-wire distributor supplies a balanced voltage of 400/230 V to a load consisting of 8 A at p.f. 0-7 lagging for R-phase, 10 A at p.f. 0-8 leading for Y phase and 12 A at unity p.f. for B phase. The resistance of each line conductor is 0.4 2. The reactance of neutral is 0.2 2. Calculate the neutral current, the supply voltage for R phase and draw the phasor diagram. The phase sequence is RYB.arrow_forwardThe three line leads of a 400/230 V, 3-phase, 4-wire supply are designated as R, Y and B respectively. The fourth wire or neutral wire is designated as N. The phase sequence is RYB. Compute the currents in the four wire when the following loads are connected to this supply: From R to N: 25 kW, unity power factor. From Y to N: 20 kVA, 0-7 lag. From B to N: 30 kVA, 0-6 lead.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
MATLAB: An Introduction with ApplicationsEngineeringISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons Inc
Essentials Of Materials Science And EngineeringEngineeringISBN:9781337385497Author:WRIGHT, Wendelin J.Publisher:Cengage,
Industrial Motor ControlEngineeringISBN:9781133691808Author:Stephen HermanPublisher:Cengage Learning
Basics Of Engineering EconomyEngineeringISBN:9780073376356Author:Leland Blank, Anthony TarquinPublisher:MCGRAW-HILL HIGHER EDUCATION
Structural Steel Design (6th Edition)EngineeringISBN:9780134589657Author:Jack C. McCormac, Stephen F. CsernakPublisher:PEARSON
Fundamentals of Materials Science and Engineering...EngineeringISBN:9781119175483Author:William D. Callister Jr., David G. RethwischPublisher:WILEY
MATLAB: An Introduction with Applications
Engineering
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Essentials Of Materials Science And Engineering
Engineering
ISBN:9781337385497
Author:WRIGHT, Wendelin J.
Publisher:Cengage,
Industrial Motor Control
Engineering
ISBN:9781133691808
Author:Stephen Herman
Publisher:Cengage Learning
Basics Of Engineering Economy
Engineering
ISBN:9780073376356
Author:Leland Blank, Anthony Tarquin
Publisher:MCGRAW-HILL HIGHER EDUCATION
Structural Steel Design (6th Edition)
Engineering
ISBN:9780134589657
Author:Jack C. McCormac, Stephen F. Csernak
Publisher:PEARSON
Fundamentals of Materials Science and Engineering...
Engineering
ISBN:9781119175483
Author:William D. Callister Jr., David G. Rethwisch
Publisher:WILEY