(a)
Write the values of modulus of resilience and modulus of toughness for titanium.
The range of modulus of resilience for titanium is
The range of modulus of toughness for titanium is
(a)

Explanation of Solution
Refer Table 17.4 “The strength of Selected Materials” in the textbook.
The range for Yield strength of titanium alloys
The range for Ultimate strength of titanium alloy
Refer Table 17.2 “Modulus of Elasticity and Shear Modulus of Selected Materials” in the textbook.
The modulus of elasticity of titanium alloy is
The elongation of titanium alloy is 23%.
Find the range of modulus of resilience
Substitute the minimum and maximum values;
Therefore, the range of modulus of resilience is
Find the range of modulus of toughness
Substitute minimum and maximum values;
Therefore, the range of modulus of toughness is
(b)
Write the values of modulus of resilience and modulus of toughness for steel.
The range of modulus of resilience for steel is
The range of modulus of toughness for steel is
(b)

Explanation of Solution
Refer Table 17.4 “The strength of Selected Materials” in the textbook.
The range for Yield strength of steel
The range for Ultimate strength of steel
Refer Table 17.2 “Modulus of Elasticity and Shear Modulus of Selected Materials” in the textbook.
The range for modulus of elasticity of steel (E) is
The elongation of steel is 15%.
Modulus of resilience:
Substitute the minimum and maximum values in Equation (1).
Therefore, the range of modulus of resilience is
Modulus of toughness;
Substitute minimum and maximum values in Equation (2);
Therefore, the range of modulus of toughness is
Want to see more full solutions like this?
Chapter 17 Solutions
Engineering Fundamentals: An Introduction to Engineering
- Please explain step by step and show formulaarrow_forwardPlease explain step by step and show formulaarrow_forwardFor an reinforced concrete two-way slab shown in figure under the load (P). (the slab continuous over all edges - all sides are fixed), Determine (By using yield line theory): A- Draw the Yield line Pattern B- Determine the moment m 3BAT C- Find The required flexural steel to resist the loads causing the slab to collapse if P = 200 KN, fc = 28 MPa, fy = 420 MPa d = 120 mm. Use 10 mm bars. (Pmin = 0.002) 6m 8m >2m->) 3marrow_forward
- 3BAT For an reinforced concrete two-way slab shown in figure under the load (P). (the slab continuous over all edges - all sides are fixed), Determine (By using yield line theory): A- Draw the Yield line Pattern B- Determine the moment m KN, fc Please don't solve in Al anco if P = 200 6m 8m 2m-)) 3marrow_forwardPlease explain step by step and show formulaarrow_forwardPlease explain step by step and show formulaarrow_forward
- 4-You are making a bookshelf (shown below) to carry books that range from 8½" to 11" in height and would take up 29" of space along the length. The material is wood having a Young's Modulus of 3.66 ksi, thickness of 3/8", and width of 12". You want to find the maximum vertical deflection of the bookshelf. The vertical deflection of the shelf is given by: -0.67665 x10 8x4 -0.26689x105 x3 +0.12748x10³ x² -0.018057=0 x Bookshelf Booksarrow_forwardThe difference in water surface levels in two tanks, which are connected by three pipes in series of lengths 300 m, 170 m, and 210 m, having diameters 300 mm, 200 mm, and 400 mm, respectively, is 12 m. Determine the rate of flow of water if coefficients of friction are 0.005, 0.0052, and 0.0048, respectively. Determine the discharge and velocity in each pipe, considering the minor losses and neglecting minor losses.arrow_forward3 BAT For an reinforced concrete two-way slab shown in figure under the load (P). (the slab continuous over all edges - all sides are fixed), Determine (By using yield line theory): A- Draw the Yield line Pattern B- Determine the moment m C- Find The required flexural steel to resist the loads causing the slab to collapse if P = 200 KN, f=28 MPa, fy = 420 MPa d = 120 mm. Use 10 mm bars. (Pmin = 0.002) 6m 8m >2m-)) 3marrow_forward
- REINFORCED CONCRETE DESIGNANALYSIS OF SINGLY REINFORCED BEAMS (STRENGTH DESIGN METHOD)Direction:Solution must be completeUse ballpen/inkpenAnswer in two decimal placesBox your final answerarrow_forwardE. Estimate the required air flow rate for the new activated sludge plant at Camp Verde Problems 23-3 — 23-823-11, and 23-14 B). Use the following assumptions in preparing the estimate: Clean water correction, a 0.70 . Salinity correction, ẞ= 0.95 . Fouling factor = 0.8 Summer wastewater temperature 22°C • Atmospheric pressure 101.325 kPa .Elevation 2,135 m Depth of aerator = 4.5 m Operating DO = 2.0 mg/L Percent oxygen leaving aeration tank - 19% Manufacturer's SOTR = 650 kg/d • Manufacturer's air flow rate at standard conditions 20 m3/d aerator 23-3. The town of Camp Verde has been directed to upgrade its primary WWTP to a secondary plant that can meet an effluent standard of 25.0 mg/L BOD5 and 30 mg/L suspended solids. They have se- lected a completely mixed activated sludge system for the upgrade. The existing primary treatment plant has a flow rate of 2,506 m³/d. The effluent from the primary tank has a BOD5 of 240 mg/L. Using the following assumptions, estimate the required…arrow_forwardOnly expert should attempt,I don't need AI solutions, because it's always incorrect pleasearrow_forward
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage LearningMaterials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage LearningConstruction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
- Solid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning




