Repeat Prob. 15–112 using a coal from Utah that has an ultimate analysis (by mass) of 61.40 percent C, 5.79 percent H2, 25.31 percent O2, 1.09 percent N2, 1.41 percent S, and 5.00 percent ash (noncombustibles).
(a)
The amount of steam generated per unit of fuel mass burned.
Answer to Problem 113RP
The amount of steam generated per unit of fuel mass burned is
Explanation of Solution
Express the number of moles of carbon.
Here, molar mass of carbon is
Express the number of moles of hydrogen.
Here, molar mass of hydrogen is
Express the number of moles of oxygen.
Here, molar mass of oxygen is
Express the number of moles of nitrogen.
Here, molar mass of nitrogen is
Express the number of moles of sulphur.
Here, molar mass of sulphur is
Express the total number of moles.
Express the mole fraction of carbon.
Express the mole fraction of hydrogen.
Express the mole fraction of oxygen.
Express the mole fraction of nitrogen.
Express the mole fraction of sulphur.
Write the energy balance equation using steady-flow equation.
Here, the total energy entering the system is
Substitute
Here, the enthalpy of formation for product is
Write the formula for the amount of steam generated per unit mass of fuel burned.
Here, the mass of the steam is
Conclusion:
Refer Table A-1, “molar mass, gas constant, and the critical point properties”, and write the molar masses.
Here, molar mass of air is
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Express the combustion equation.
Here, carbon dioxide, water, sulfur dioxide, nitrogen and oxygen is
Perform the species balancing according to the oxygen balance:
Oxygen balance:
Substitute
Calculate the apparent molecular weight of the cool.
Refer Appendix Table A-18, A-19, A-20, and A-23, obtain the enthalpy of formation, at 298 K , and 500 K for
Substance | |||
0 | 8682 | 14,770 | |
0 | 8669 | 14,581 | |
-241820 | 9904 | 16,828 | |
-393,520 | 9364 | 17,678 |
Substitute the value of substance in Equation (XIII).
Calculate the heat loss per unit mass of the fuel.
Substitute
Thus, the amount of steam generated per unit of fuel mass burned is
(b)
The change in the exergy of the combustion steams, in
Answer to Problem 113RP
The change in the exergy of the combustion steams, in
Explanation of Solution
Write the expression for entropy generation during this process.
Write the combustion equation of Equation (VI)
Here, the entropy of the product is
Determine the entropy at the partial pressure of the components.
Here, the partial pressure is
Write the expression for exergy change of the combustion steam is equal to the exergy destruction.
Here, the thermodynamic temperature of the surrounding is
Conclusion:
Refer Equation (XIX) for reactant and product to calculation the entropy in tabular form as:
For reactant entropy,
Substance |
(T, 1 atm) | ||||
0.5758 | 0.5758 | 5.74 | -4.589 | 5.95 | |
0.3258 | 0.3258 | 130.68 | -9.324 | 45.61 | |
0.0890 | 0.0890 | 205.04 | -20.11 | 20.04 | |
0.00438 | 0.00438 | 191.61 | -45.15 | 1.04 | |
0.9821 | 0.21 | 205.04 | -12.98 | 214.12 | |
3.693 | 0.79 | 191.61 | -1.960 | 714.85 | |
For product entropy,
Substance |
(T, 1 atm) | ||||
0.5758 | 0.1170 | 234.814 | -17.84 | 145.48 | |
0.3258 | 0.0662 | 206.413 | -22.57 | 74.60 | |
0.3274 | 0.0665 | 220.589 | -22.54 | 79.60 | |
3.693 | 0.7503 | 206.630 | -2.388 | 771.90 | |
Substitute
Substitute
Calculate the exergy destruction per unit mass of the basis.
Thus, the change in the exergy of the combustion steams, in
(c)
The exergy change of the steam, in
Answer to Problem 113RP
The exergy change of the steam, in
Explanation of Solution
Determine the exergy change of the steam stream.
Here, the final enthalpy is
Conclusion:
Substitute
Thus, the exergy change of the steam, in
(d)
The lost work potential, in
Answer to Problem 113RP
The lost work potential, in
Explanation of Solution
Determine the lost work potential is the negative of the net exergy change both streams.
Conclusion:
Substitute
Thus, the lost work potential, in
Want to see more full solutions like this?
Chapter 15 Solutions
THERMODYNAMICS LLF W/ CONNECT ACCESS
- A crate weighs 530 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the xy plane. Point A is located at a height of h = 42 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. 2013 Michael Swanbom ↑ Z C BY NC SA b x B у D Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 30 in b 43 in с 4.5 in The tension in rope AB is lb The tension in rope AC is lb The tension in rope AD is lbarrow_forwardThe airplane weighs 144100 lbs and flies at constant speed and trajectory given by 0 on the figure. The plane experiences a drag force of 73620 lbs. a.) If = 11.3°, determine the thrust and lift forces required to maintain this speed and trajectory. b.) Next consider the case where is unknown, but it is known that the lift force is equal to 7.8 times the quantity (Fthrust Fdrag). Compute the resulting trajectory angle - and the lift force in this case. Use the same values for the weight and drag forces as you used for part a. Уллу Fdrag 10. Ө Fthrust cc 10 2013 Michael Swanbom BY NC SA Flift Fweight The lift force acts in the y' direction. The weight acts in the negative y direction. The thrust and drag forces act in the positive and negative x' directions respectively. Part (a) The thrust force is equal to lbs. The lift force is equal to Part (b) The trajectory angle is equal to deg. The lift force is equal to lbs. lbs.arrow_forwardThe hoist consists of a single rope and an arrangement of frictionless pulleys as shown. If the angle 0 = 59°, determine the force that must be applied to the rope, Frope, to lift a load of 4.4 kN. The three-pulley and hook assembly at the center of the system has a mass of 22.5 kg with a center of mass that lies on the line of action of the force applied to the hook. e ΘΕ B CC 10 BY NC SA 2013 Michael Swanbom Fhook Note the figure may not be to scale. Frope = KN HO Fropearrow_forward
- Determine the tension developed in cables AB and AC and the force developed along strut AD for equilibrium of the 400-lb crate. x. 5.5 ft C 2 ft Z 2 ft D 6 ft B 4 ft A 2.5 ftarrow_forwardA block of mass m hangs from the end of bar AB that is 7.2 meters long and connected to the wall in the xz plane. The bar is supported at A by a ball joint such that it carries only a compressive force along its axis. The bar is supported at end B by cables BD and BC that connect to the xz plane at points C and D respectively with coordinates given in the figure. Cable BD is elastic and can be modeled as a linear spring with a spring constant k = 400 N/m and unstretched length of 6.34 meters. Determine the mass m, the compressive force in beam AB and the tension force in cable BC. Z D (c, 0, d) C (a, 0, b), A e B y f m BY NC SA x 2016 Eric Davishahl Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 8.1 m b 3.3 m C 2.7 m d 3.9 m e 2 m f 5.4 m The mass of the block is The compressive force in bar AB is The tension in cable S is N. kg.arrow_forwardTwo squirrels are sitting on the rope as shown. The squirrel at A has a weight of 1.2 lb. The squirrel at B found less food this season and has a weight of 0.8 lb. The angles 0 and > are equal to 50° and 60° respectively. Determine the tension force in each of the rope segments (T₁ in segment, T₂ in segment Я, and T3 in segment DD) as well as the angle a in degrees. Ө A α B Note the figure may not be to scale. T₁ = lb lb T2 T3 = = lb απ deg A BY NC SA 2013 Michael Swanbomarrow_forward
- Each cord can sustain a maximum tension of 500 N. Determine the largest mass of pipe that can be supported. B 60° A E Harrow_forward2. Link BD consists of a single bar 1 in. wide and 0.5 in. thick. Knowing that each pin has a in. diameter, determine (a) the maximum value of the normal stress in link BD and the bearing stress in link BD if 0 = 0, (b) the maximum value of the normal stress in link BD if 0 = 90. -6 in.- 12 in. 30° D 4 kipsarrow_forwardIn the image is a right rectangular pyramid of total mass m. Note the location of point Q. Determine the inertia dyadic for the pyramid P, relative to point Q for e hat unit vectors.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY