From one corner of a thin homogeneous square metal sheet with sides of L = 20 cm is cut an L/2 square sheet as shown in the figure. Approximately how far away is the centre of mass of the resulting shape from the centre P of the original square? P ○ 24 mm ○ 42 mm ○ 32 mm ○ 16 mm

20:19 Vol 69% + WiFi2 nothing happens to the nqara lever more the container (d) none of these 33. Statement I: The internal energy of a solid substance increases during melting.4_03-04-2025_QP.pdf Statement II: The molecules have greater kinetic energy in a liquid. Statement I and Statement II are true and the (a) Statement II is the correct explanation of Statement I. Statement I and Statement II are true but the (b) Statement II is not the correct explanation of Statement I. (c) Statement I is true but Statement II is false. (d) Statement I and Statement II are false. 34. Select correct statement related to heat 35. (a) Heat is possessed by a body (b) (c) Hot water contains more heat as compared to cold water Heat is the energy which flows due to temperature difference (d) All of these Two liquids A and B are at 32°C and 24°C. When mixed in equal masses the temperature of the mixture is found to be 28°C. Their specific heats are in the ratio of: (a) 3:2 (c) 1:1 (b) 2:3 (d) 4:3 36.…

The skid loader shown has a mass of 1.28 Mg and in the position shown the center of mass is at G. There is a 255 kg barrel in the bucket with its center of mass at GB. The horizontal distance between the barrel's center of mass and the front wheels is d = 1.33 m. The horizontal distance between the front wheels and rear wheels is w = 0.55 m. The bucket arm is held horizontal between D and E and the pair of hydraulic cylinders creates angle /EDC of 0 = 32 degrees. 1.25 m GB D 60000 A G B E C 0.15 m 0.5 m d W i. Determine the reaction force on the pair of wheels at the front of the skid loader at A. ii. Determine the reaction force on the pair of wheels at the rear of the skid loader at B. iii. Determine the magnitude of the compressive force in a single hydraulic cylinder CD. Note that there are two hydraulic cylinders, one on each side of the skid loader. iv. Determine the magnitude of the reaction force on a single pin that attaches the bucket assembly to the skid loader chassis at E.…

The truss structure below is subjected to three forces as shown. P₁ = 7.5 kN P2 = 10.5 kN P3 = 6.5 kN h = 3.5 m w= 2.7 m A W B F E P3 P1 W C P2 W Ꭰ h i. Identify any Zero Force Members. ii. Calculate the support reaction forces at A and D. iii. Calculate the magnitude of the force in members EF, CF, BC, DE, and CD and state if these members are in tension or compression.

Part A Consider the mechanism shown in (Figure 1). If a force of F = 350 N is applied to the handle of the toggle clamp, determine the resulting clamping force at A. Express your answer to three significant figures and include the appropriate units. Figure -235 mm- 30 mm 70 mm 30 mm/ 30 275 mm 1 of 1 > ΜΑ ? FA= Value Units Submit Request Answer Return to Assignment Provide Feedback

got 4.67 for 1 then 9.33 for the rest then 21.33 for the input and output but it says all are wrong

mase as shown 2) A holy of once sty extually at rest & acted upon by bus mutually perpendicular forces 12 Nand 5N belowilf the particle moves in derection Calculato the magnitude of the acceleration of 12nt R 0 so A SN

Required information Two speakers vibrate in phase with each other at 523 Hz. At certain points in the room, the sound waves from the two speakers interfere destructively. One such point is 1.45 m from speaker #1 and is between 2.00 m and 4.00 m from speaker #2. The speed of sound in air is 343 m/s. How far is this point from speaker #2? m

a) Consider the following function, where A is a constant. y(x,t) = A(x — vt). Can this represent a wave that travels along? Explain. b) Which of the following are possible traveling waves, provide your reasoning and give the velocity of the wave if it can be a traveling wave. e-(a²x²+b²²-2abtx b.1) y(x,t) b.2) y(x,t) = = A sin(ax² - bt²). 2 b.3) y(x,t) = A sin 2π (+) b.4) y(x,t) = A cos² 2π(t-x). b.5) y(x,t) = A cos wt sin(kx - wt)