Fundamentals Of Thermal-fluid Sciences In Si Units
Fundamentals Of Thermal-fluid Sciences In Si Units
5th Edition
ISBN: 9789814720953
Author: Yunus Cengel, Robert Turner, John Cimbala
Publisher: McGraw-Hill Education
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 14, Problem 44P
To determine

The expression for the variation of water height with respect to time.

Expert Solution & Answer
Check Mark

Explanation of Solution

Given:

Height of the cone is H.

Base radius of the cone is R.

The cross section area of the hole is Ah.

The discharge coefficient is Cd.

Velocity of water is V.

Calculation:

From the law of conservation of mass,

  ddtCVdV+V˙outV˙in=0dVCVdt+0V˙in=0dVCVdt=V˙indVCVdt=CdAhv        (I)

The volume of water at any time is given by the relation,

  VCV=πh3(R2+rR+r2)        (II)

The cross section of the cone is shown below.

Fundamentals Of Thermal-fluid Sciences In Si Units, Chapter 14, Problem 44P

From the diagram,

  r=RH(Hh)=RRHh        (III)

Substitute, Equation (III) in Equation (II).

  VCV=πh3[R2+(RRHh)R+(RRHh)2]=πhR23[1+(HhH)+(HhH)2]=πhR23H2[H2+(H2hH)+(H2+h22hH)]=πhR23H2(3H23hH+h2)=πR23H2(3hH23h2H+h3)        (IV)

Substitute Equation (IV) in Equation (I).

  ddt[πR23H2(3hH23h2H+h3)]=CdAhvπR23H2(3H2dhdt6hHdhdt+3h2dhdt)=CdAhvπR2H2(H22hH+h2)dhdt=CdAhvπR2H2(Hh)2dhdt=CdAhv(Hh)2dh=CdAhvH2πR2dt

Integrating the above equation,

  (Hh)2dh=CdAhvH2πR2dt13(Hh)3=CdAhvH2πR2t+C        (V)

Substituting, h(0)=0 in the above equation.

  13(H0)3=CdAhvH2πR2(0)+CC=H33

Rewrite Equation (V).

  13(Hh)3=CdAhvH2πR2tH33(Hh)3=H33CdAhvH2πR2tHh=H33CdAhvH2πR2t3h=HH33CdAhvH2πR2t3

Thus, the relation for variation of water height with time is h=HH33CdAhvH2πR2t3.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Assignment 10, Question 4, Problem Book #202 Problem Statement An ideal Brayton cycle with a two-stage compressor, a two-stage turbine, and a regenerator operates with a mass flow rate of 25 kg/s. The regenerator cold inlet is at 490 K and its effectiveness is 60%. Ambient conditions are 90 kPa and 20°C. The intercooler operates at 450 kPa and the reheater operates at 550 kPa. The temperature at the exit of the combustion chamber is 1,400 K. Heat is removed in the intercooler at a rate of 2.5 MW and heat is added in the reheater at a rate of 10 MW. Determine the thermal efficiency and the back work ratio. Use a cold air standard analysis with cp = 1.005 kJ/(kg K) and k = 1.4. . Answer Table Stage Description Your Answer Correct Answer Due Date Grade (%) 1 Thermal efficiency (%) Dec 5, 2024 11:59 pm 0.0 1 Weight Attempt Action/Message 1/5 Part Type Submit 1 Back work ratio (%) Dec 5, 2024 11:59 pm 0.0 1 * Correct answers will only show after due date has passed.
Assignment 10, Question 3, Problem Book #198 Problem Statement Consider a Brayton cycle with a regenerator. The regenerator has an effectiveness of 75%. The compressor inlet conditions are 1.2 bar and 300 K and the mass flowrate is 4.5 kg/s. The compressor outlet pressure is 9 bar. Both the compressor and turbine consist of a single isentropic stage. What minimum power output must be achieved before the regenerator begins to have a benefit? Use an air-standard analysis. Answer Table Correct Answer Stage Description Your Answer Due Date Grade (%) Part Weight Attempt Action/Message Туре 1 Power output (MW) Dec 5, 2024 11:59 pm 0.0 1 1/5 Submit * Correct answers will only show after due date has passed.
Q-3 Consider an engine operating on the ideal Diesel cycle with air as the working fluid. The volume of the cylinder is 1200 cm³ at the beginning of the Compression process, 75 cm³ at the end, and 150 cm³ after the heat addition process. Air is at 17°c and lookpa at the beginning of the compression proc ess. Determine @ The pressure at the beginning of the heat rejection process. the net work per cycle in kjⒸthe mean effective pressur. Answers @264.3 KN/m² ②0.784 kj or 544-6 kj © 697 KN 19 2 m

Chapter 14 Solutions

Fundamentals Of Thermal-fluid Sciences In Si Units

Ch. 14 - Shown here is a cool picture of water being...Ch. 14 - Someone claims that the volume flow rate in a...Ch. 14 - Someone claims that the average velocity in a...Ch. 14 - Someone claims that the shear stress at the center...Ch. 14 - Someone claims that in fully developed turbulent...Ch. 14 - How does the wall shear stress τw vary along the...Ch. 14 - In the fully developed region of flow in a...Ch. 14 - How is the friction factor for flow in a pipe...Ch. 14 - Discuss whether fully developed pipe flow is one-,...Ch. 14 - Consider fully developed flow in a circular pipe...Ch. 14 - Consider fully developed laminar flow in a...Ch. 14 - Explain why the friction factor is independent of...Ch. 14 - What is turbulent viscosity? What causes it? Ch. 14 - Consider fully developed laminar flow in a...Ch. 14 - How is head loss related to pressure loss? For a...Ch. 14 - Consider laminar flow of air in a circular pipe...Ch. 14 - What is the physical mechanism that causes the...Ch. 14 - The velocity profile for the fully developed...Ch. 14 - Water flows steadily through a reducing pipe...Ch. 14 - Water at 10°C (ρ = 999.7 kg/m3 and μ = 1.307 ×...Ch. 14 - Consider an air solar collector that is 1 m wide...Ch. 14 - Heated air at 1 atm and 100°F is to be transported...Ch. 14 - In fully developed laminar flow in a circular...Ch. 14 - The velocity profile in fully developed laminar...Ch. 14 - Repeat Prob. 14–34 for a pipe of inner radius 7...Ch. 14 - Water at 15°C (ρ = 999.1 kg/m3 and μ = 1.138 ×...Ch. 14 - Consider laminar flow of a fluid through a square...Ch. 14 - Repeat Prob. 14–37 for turbulent flow in smooth...Ch. 14 - Air enters a 10-m-long section of a rectangular...Ch. 14 - Water at 70°F passes through...Ch. 14 - Oil with ρ = 876 kg/m3 and μ = 0.24 kg/m·s is...Ch. 14 - Glycerin at 40°C with ρ = 1252 kg/m3 and μ = 0.27...Ch. 14 - Air at 1 atm and 60°F is flowing through a 1 ft ×...Ch. 14 - Prob. 44PCh. 14 - Prob. 45PCh. 14 - Oil with a density of 850 kg/m3 and kinematic...Ch. 14 - Prob. 47PCh. 14 - Prob. 48PCh. 14 - Prob. 50PCh. 14 - Prob. 51PCh. 14 - Prob. 52PCh. 14 - Prob. 53PCh. 14 - Prob. 54PCh. 14 - Prob. 55PCh. 14 - Prob. 56PCh. 14 - Prob. 57PCh. 14 - Water is to be withdrawn from an 8-m-high water...Ch. 14 - Prob. 59PCh. 14 - Prob. 60PCh. 14 - Prob. 61PCh. 14 - Prob. 62PCh. 14 - Prob. 63PCh. 14 - Prob. 64PCh. 14 - Consider two identical 2-m-high open tanks filled...Ch. 14 - A piping system involves two pipes of different...Ch. 14 - Prob. 67PCh. 14 - Prob. 68PCh. 14 - Prob. 69PCh. 14 - Prob. 70PCh. 14 - The water needs of a small farm are to be met by...Ch. 14 - Prob. 72PCh. 14 - Prob. 73PCh. 14 - Prob. 74PCh. 14 - Prob. 75PCh. 14 - Prob. 76PCh. 14 - Prob. 77PCh. 14 - Prob. 78PCh. 14 - Prob. 80PCh. 14 - Prob. 81PCh. 14 - A vented tanker is to be filled with fuel oil with...Ch. 14 - Two pipes of identical length and material are...Ch. 14 - Prob. 84PCh. 14 - Prob. 85PCh. 14 - Prob. 86PCh. 14 - Prob. 87PCh. 14 - Prob. 88PCh. 14 - Prob. 90PCh. 14 - Prob. 91PCh. 14 - Prob. 92PCh. 14 - Prob. 93PCh. 14 - Prob. 94RQCh. 14 - Prob. 95RQCh. 14 - Prob. 96RQCh. 14 - Prob. 97RQCh. 14 - Prob. 98RQCh. 14 - Prob. 99RQCh. 14 - Repeat Prob. 14–99E assuming the pipe is inclined...Ch. 14 - Prob. 101RQCh. 14 - Prob. 102RQCh. 14 - Prob. 103RQCh. 14 - Prob. 104RQCh. 14 - Two pipes of identical diameter and material are...Ch. 14 - Prob. 106RQCh. 14 - Prob. 107RQCh. 14 - Prob. 108RQCh. 14 - Prob. 109RQCh. 14 - Prob. 110RQCh. 14 - Prob. 111RQCh. 14 - Prob. 112RQCh. 14 - Prob. 114RQCh. 14 - Prob. 115RQCh. 14 - Prob. 116RQCh. 14 - Prob. 118RQ
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License