
Concept explainers
Suppose that the free surface of the inlet reservoir in Prob. 13-39 is 3.0 m higher in elevation, such that Z2- z1= 4.85 m. All the constants and parameters are identical to those of Prob. 14-39 except for the elevation difference. Calculate the volume flow rate for this case and compare with the result of Prob. 14-39. Discuss.

The volume flow rate by the pump.
Answer to Problem 41P
The volume flow rate by the pump is
Explanation of Solution
Given information:
The diameter of pipe is
Write the expression for head required.
Here, pressure at exit is
Write the expression for coefficient of total minor head loss.
Here, coefficient of entrance loss is
Write the expression for head loss.
Here, length of pipe is
Write the expression for
Here, shutoff head is
Write the expression for Reynolds number.
Here, density of water is
Write the expression for Colebrook equation.
Here, coefficient of friction is
Write the expression for volume flow rate.
Calculation:
Substitute
Substitute
Substitute
Substitute
Refer Table-A-3 "Properties of saturated water" at
Substitute
Substitute
Substitute
Here, apply hit and trial to obtain velocity of flow.
Trial-(1)
Substitute
Since the values on both sides are not equal, so assumption
Trial-(2)
Substitute
Here, the values on both sides are equal, so velocity of flow is
Substitute
Here, the volume flow rate for elevation difference of
Since the volume flow rate for the for the elevation difference of
Hence on decreasing elevation difference between the reservoir the volume flow rate increases.
Conclusion:
The volume capacity delivered by the pump is
Want to see more full solutions like this?
Chapter 14 Solutions
EBK FLUID MECHANICS: FUNDAMENTALS AND A
- Sketch and describe hatch coamings. Describe structrual requirements to deck plating to compensate discontinuity for corners of a hatch. Show what is done to the deck plating when the decks are cut away and include the supporting members.arrow_forwardAn Inclining experiment done on a ship thats 6500 t, a mass of 30t was moved 6.0 m transvesly causing a 30 cm deflection in a 6m pendulum, calculate the transverse meta centre height.arrow_forwarda ship 150 m long and 20.5 m beam floats at a draught of8 m and displaces 19 500 tonne. The TPC is 26.5 and midshipsection area coefficient 0.94. Calculate the block, prismatic andwaterplane area coefficients.arrow_forward
- A vessel loads 680 t fuel between forward and aft deep tanks. centre of gravity of forward tank is 24m forward of ships COG. centre to centre between tanks is 42 m. how much in each tank to keep trim the samearrow_forwardBeam of a vessel is 11% its length. Cw =0.72. When floating in SW of relative denisity 1.03, TPC is 0.35t greater than in freshwater. Find the length of the shiparrow_forwardAn inclining experiment was carried out on a ship of 4000tonne displacement, when masses of 6 tonne were moved transverselythrough 13.5 m. The deflections of a 7.5 m pendulurnwere 81, 78, 85, 83, 79, 82, 84 and 80 mm respectively.Caiculate the metacentric height.arrow_forward
- A ship of 10 000 tonne displacement has a waterplanearea of 1300 m2. The ship loads in water of 1.010 t/m3 andmoves into water of 1.026 t/m3. Find the change in meandraughtarrow_forwardA ship of 7000 tonne displacement has a waterplane areaof 1500 m2. In passing from sea water into river water of1005 kg/m3 there is an increase in draught of 10 cm. Find the Idensity of the sea water.arrow_forwardA ship has 300 tonne of cargo in the hold, 24 m forward ofmidships. The displacement of the vessel is 6000 tonne and its centre of gravity is 1.2 m forward of midships.Find the new position of the centre of gravity if this cargo ismoved to an after hold, 40 m from midshipsarrow_forward
- Sketch and describe how ships are supported in dry dock. When and where does the greatest amount of stresses occur?arrow_forwardSketch and desribe a balanced rudder and how it is suspendedarrow_forwardA ship 140 m long and 18 m beam floats at a draught of9 m. The immersed cross-sectionai areas at equai intervais are 5,60, 116, 145, 152, 153, 153, 151, 142, 85 and 0 m2 respectively.Calculate:(a) displacement(b) block coefficient(c) midship section area coefficient(d) prismatic coefficient.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





