Explanation P ( B | A ) P ( A | B ) Conditional probability of the event B given is event A . Conditional probability of the event A given in event B P ( B | A ) = P ( B ∩ A ) P ( A ) P ( B |

6th Edition

ISBN: 9780134434681

Author: Tom Pirnot

Publisher: PEARSON

See similar textbooks

Concept explainers

Statements and Logic

Logic is the analysis of general patterns of thoughts without regard to any specific sense of context.

Videos

Question

Chapter 13.CT, Problem 5CT

To determine

To explain:

The difference in the meaning between P(B|A) and P(A|B).

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 13.CT, Problem 4CT

Chapter 13.CT, Problem 6CT

Students have asked these similar questions

Question 5 A fraction nonconforming control chart with center line 0.10, UCL = 0.19, and LCL = 0.01 is used to control a process. (a) If three-sigma limits are used, find the sample size for the control charte 2 (b) Use the Poisson approximation to the binomial to find the probability of type I error. (c) Use the Poisson approximation to the binomial to find the probability of type II error if the process fraction defective is actually p = 0.20.

Question 8 Ten parts are measured three times by the same operator in a gauge capability study. The data are shown in Table 4. (a) Describe the measurement error that results from the use of this gauge. I (b) Estimate total variability and product variability. (c) What percentage of total variability is due to the gauge? (d) If specifications on the part are at 100±15, find the P/T ratio for this gauge. Comment on the adequacy of the gauge. 3 Table 4: Measurement Data for Question 8 Part Number Measurement 1 Measurement 2 Measurement 3 1 2 100 95 101 100 93 97 3 101 103 100 4 96 95 97 5 98 98 96 6 99 98 98 7889 95 97 98 100 99 98 100 100 97 10 100 98 98 99

Question 6 The data shown in Table 3 are and R values for 24 samples of size n = 5 taken from a process producing bearings. The measurements are made on the inside diameter of the bearing, with only the last three decimals recorded (i.e., 34.5 should be 0.50345). Perform a process capability analysis using and R charts for the data from Table 3. Table 3: Data for Question 6 Sample Number R | Sample Number I Ꭱ 1 34.5 3 13 35.4 8 2 34.2 4 14 34.0 6 ∞∞ 31.6 15 37.1 5 4 31.5 4 16 34.9 7 56789 35.0 5 17 33.5 4 34.1 6 18 31.7 3 32.6 4 19 34.0 8 33.8 3 20 35.1 4 34.8 7 10 33.6 8 11 31.9 3 12 38.6 9 2232 21 33.7 2 32.8 1 33.5 24 34.2 2 32 3

Chapter 13 Solutions

Mathematics All Around (6th Edition)

Ch. 13.1 - In Exercises 14 , write each event as a set of...Ch. 13.1 - In Exercises 14 , write each event as a set of...Ch. 13.1 - In Exercises 14 , write each event as a set of...Ch. 13.1 - Prob. 4E Ch. 13.1 - In Exercises 58, use the given spinner to write...Ch. 13.1 - Prob. 6E Ch. 13.1 - In Exercises 58, use the given spinner to write...Ch. 13.1 - In Exercises 58, use the given spinner to write...Ch. 13.1 - We are rolling two four-sided dice having the...Ch. 13.1 - We are rolling two four-sided dice. One die has...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, subject and related others by exploring similar questions and additional content below.