Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 13, Problem 9ETSQ
To determine
The appropriate casting technique for a very complex metal shape which cannot be removed from a mold.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
I need the answer as soon as possible
The most common method for production of steel is
Group of answer choices
Slip casting
Continuous casting
Hot pressing
Investment casting
please quickly thanks !
Chapter 13 Solutions
Materials Science And Engineering Properties
Ch. 13 - Prob. 1CQCh. 13 - Prob. 2CQCh. 13 - Prob. 3CQCh. 13 - Prob. 4CQCh. 13 - Prob. 5CQCh. 13 - Prob. 6CQCh. 13 - Prob. 7CQCh. 13 - Prob. 8CQCh. 13 - Prob. 9CQCh. 13 - Prob. 10CQ
Ch. 13 - Prob. 11CQCh. 13 - Prob. 12CQCh. 13 - Prob. 13CQCh. 13 - Prob. 14CQCh. 13 - Prob. 15CQCh. 13 - Prob. 16CQCh. 13 - Prob. 17CQCh. 13 - Prob. 18CQCh. 13 - Prob. 19CQCh. 13 - Prob. 1ETSQCh. 13 - Prob. 2ETSQCh. 13 - Prob. 3ETSQCh. 13 - Prob. 4ETSQCh. 13 - Prob. 5ETSQCh. 13 - Prob. 6ETSQCh. 13 - Prob. 7ETSQCh. 13 - Prob. 8ETSQCh. 13 - Prob. 9ETSQCh. 13 - Prob. 10ETSQCh. 13 - Prob. 11ETSQCh. 13 - Prob. 12ETSQCh. 13 - Prob. 13ETSQCh. 13 - Prob. 14ETSQCh. 13 - Prob. 15ETSQCh. 13 - Prob. 16ETSQ
Knowledge Booster
Similar questions
- The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.arrow_forwardKindly select the correct answer with solutions or explanationsarrow_forwardThe volume and mass are changed with Both options are above Forming process. O Cutting process.arrow_forward
- i need quickly please please please Which of these cast iron would allow the greatest amount of plastic deformation before fracture . Nodular cast iron Grey cast iron White cast iron None of them can be worked. If the diameter of steel specimen stretched by tension load is doubled , then it’s tensile strength will be Halved Remain unaffected Doubled Become four times Temperature is proportional with Percent of elongation Tensile strength Modulus of elasticity All above The tensile strength of a steel specimen that have a 182 HB , equals to 490 MPa 910 MPa 627 MPa Not given…arrow_forward(a) In general, which provides better fire performance, carbonate or silicate aggregates? Why? (b) Why does fire design incorporate a load reduction factor (Dfire) = 1.0? (c) Two identical beams (Beam 1 is simply supported, and Beam 2 is fully restrained) are heated under similar conditions. What does the mechanical strain equal to in each of these beams? (d) A design office located in Clemson, SC (with a branch in San Francisco, CA) envisions designing a new composite member made of steel and timber. This to-be designed member is expected to be used in wildfire-prone regions primarily for single family homes. Comment on how you would design such a member to achieve superior fire performance. (e) Plot and discuss the expected degradation faces in three bending elements (say, beams) to be made from concrete, steel and timber?arrow_forwardDecode the characteristics of a 6063 T831 aluminum.arrow_forward
- What are the classification of steel and explain the contain , the characteristics and applications of this steelarrow_forwardExperimental results show that in EBW the penetration depth of the weld decreases as the welding speed increases. Explain why. Under the same power and welding speed, do you expect a much greater penetration depth in aluminum or steel and why?arrow_forward(a) the modulus of elasticity in GPa for the Aluminum B) the proportional limit in MPa for the Aluminum C) the ultimate strength in MPa for the Aluminum D) Ductility of material based on percent elongationarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Construction Materials, Methods and Techniques (M...
Civil Engineering
ISBN:9781305086272
Author:William P. Spence, Eva Kultermann
Publisher:Cengage Learning