Concept explainers
The diameter of the third channel.
Answer to Problem 53P
The diameter of the channel 3 is
Explanation of Solution
Given Information:
The figure below represents the cross -section of three channels.
Figure-(1)
The diameter of channel 1 is
Write the expression for flow rate from channel 1 and channel 2.
Here, the manning's coefficient for channel 1 is
Write the expression for flow rate through the channel 3.
Here, the manning's coefficient for channel 3 is
Write the expression for the cross sectional flow area of channel1.
Here, the radius of the channel 1 is
Write the expression for the cross sectional flow area of channel 2.
Here, the radius of the channel 2 is
Write the expression for the cross sectional flow area of channel 3.
Here, the radius of the channel 3 is
Write the expression to calculate the wetted perimeter of the channel 1.
Write the expression to calculate the wetted perimeter of the channel 2.
Write the expression to calculate the wetted perimeter of the channel 3.
Write the expression to calculate the hydraulic radius of channel 1.
Write the expression to calculate the hydraulic radius of channel 2.
Write the expression to calculate the hydraulic radius of channel 3.
Write the expression to calculate the diameter of the channel 3.
Calculation:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Refer to Table (13.1), "Mean values of the Manning Coefficient for water flow in open channels" to obtain the value of
Substitute
Substitute
Substitute
Conclusion:
The diameter of the channel 3 is
Want to see more full solutions like this?
Chapter 13 Solutions
EBK FLUID MECHANICS: FUNDAMENTALS AND A
- A submerged sharp crested weir 0.81 m high stands clear across a channel having vertical sides and width of 3.15 m. The depth of water in the channel of approach is 1.26 m, and 10.5 m downstream from the weir the depth of water is 0.93 m. Determine the discharge in litres per minute. Assume Cd1 = 0.58 and Cd2 = 0.80.arrow_forwardWater is flowing uniformly in a finished-concrete channel of trapezoidal cross section with a bottom width of 0.8 m, trapezoid angle of 50°, and a bottom angle of 0.4°. If the flow depth is measured to be 0.52 m, determine the flow rate of water through the channel.arrow_forwardIn order to determine the flow in a rectangular channel, a 75-mm-high bump is added on its bottom surface. The measured depth of flow at the bump is 1.25 m. The flow is uniform throughout the cross-sections at A and B, and the channel has a width of 1.2 m. Assume the fluid is an ideal fluid, that is, incompressible and frictionless. B 1.25 m 1.5 m 75 mm Part A Determine the volumetric discharge. Express your answer to three significant figures and include the appropriate units.arrow_forward
- The flow rate of water flowing in a 5-m-wide channel is to be measured with a sharp-crested triangular weir 0.5 m above the channel bottom with a notch angle of 80°. If the flow depth upstream from the weir is 1.5 m, determine the flow rate of water through the channel. Take the weir discharge coefficient to be 0.60.arrow_forwardWater is flowing in an open channel as shown below at a depth of 2m and a velocity of 3m/sec. It then flows down a chute into another channel where the depth is Im and the velocity is 10m/sec. assuming frictionless flow; determine the difference in elevation of the channel floors. 3 m/sec 10m/sec 1marrow_forwardA sluice gate discharges water into a horizontal rectangular channel with a velocity of 7.5 m/s and depth of flow (d1) is 0.35m. The width of the channel is 8m. Determine whether a hydraulic jump will occur and if so, find its height and loss of energy per kg of water. Also determine the power lost in the hydraulic jump. Sluice gate H Hydraulic d2 jump diarrow_forward
- The bottom slope of a hydraulically optimum rectangular duct is 0.045 and the Manning friction coefficient is 0.025. If the height of the hydraulic jump formed in this channel is H = 3.5m; How many meters (m) are the energy losses due to the hydraulic jump?arrow_forwardWater flows through a tube with a regular hexagonal cross-section whose side is 0.7 cm. Determine the hydraulic diameter (DH) of the tube in cm.arrow_forwardThe specific energy for a 3 m wide channel is to be 3 kg-m/kg. What would be the maximum possible discharge?arrow_forward
- Find the wetted area if wetted perimeter is 16 m Hydraulic radius is 1.5 marrow_forwardDetermine the discharge through three new cast-iron pipe connected in series, having diameters of 250mm, 200mm, 150mm and lengths of 600m, 360m and 270m respectively, When the total friction loss not including the minor losses is 5.0 m. Assume f=0.024 for all pipes.( hint: apply H= f.L.V²/( D.2.g)₁ + f.L.V²/( D.2.g)₂ + f.L.V²/( D.2.g)₃ and Q1=Q2=Q3 where Q=A.V ).arrow_forwardWater flows uniformly half-full in a 2-m-diameter circular channel that is laid on a grade of 1.5 m/km. If the channel is constructed of finished concrete, determine the flow rate of the water.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY