EBK 3I-EBK: WELDING PRINCIPLES & APPLIC
8th Edition
ISBN: 9780176919764
Author: Jeffus
Publisher: VST
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 13, Problem 21R
Why should there be a space between the plates when making a fillet weld on thick plates of a tee joint?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
5.112 A mounting bracket for electronic components is formed from sheet
metal with a uniform thickness. Locate the center of gravity of the
bracket.
0.75 in.
3 in.
༧
Fig. P5.112
1.25 in.
0.75 in.
y
r = 0.625 in.
2.5 in.
1 in.
6 in.
x
4-105. Replace the force system acting on the beam by an equivalent resultant force and couple
moment at point B.
A
30 in.
4 in.
12 in.
16 in.
B
30%
3 in.
10 in.
250 lb
260 lb
13
5
12
300 lb
Sketch and Describe a hatch coaming and show how the hatch coamings are framed in to ships strucure?
Chapter 13 Solutions
EBK 3I-EBK: WELDING PRINCIPLES & APPLIC
Ch. 13 - Why is it important to make sure that an FCA...Ch. 13 - What major safety concerns should an FCA welder be...Ch. 13 - Why should the FCA welding practice plates be...Ch. 13 - Why should the FCA welds be of substantial length?Ch. 13 - What must be done to a shielding gas cylinder...Ch. 13 - What can happen to the wire if the conduit is...Ch. 13 - Why is it a good idea for a new student welder to...Ch. 13 - Why is the curl in the wire end straightened out?Ch. 13 - What problems can a high-feed roller pressure...Ch. 13 - Referring to Table 13-1, answer the following a....
Ch. 13 - What are the disadvantages of beveling plates for...Ch. 13 - What is the maximum plate thickness that an FCS...Ch. 13 - What is the smallest V-groove angle that can be...Ch. 13 - What is the purpose of the root pass?Ch. 13 - Why is the FCA welding process not used for...Ch. 13 - Why should convex weld faces be avoided?Ch. 13 - What bead pattern is best for overhead welds?Ch. 13 - Why is the appearance of the cover pass so...Ch. 13 - What are the visual inspection standard's...Ch. 13 - Why is the backing strip 2 in. (50 mm) longer than...Ch. 13 - Why should there be a space between the plates...Ch. 13 - What would a small notch at the root weld's...Ch. 13 - What changes should be made in the setup for...Ch. 13 - What problem must be overcome if the amperage and...Ch. 13 - How can higher welding speeds help control...Ch. 13 - How can spatter buildup on the welding gun be...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Sketch and describe hatch coamings. Describe structrual requirements to deck plating to compensate discontinuity for corners of a hatch. Show what is done to the deck plating when the decks are cut away and include the supporting members.arrow_forwardAn Inclining experiment done on a ship thats 6500 t, a mass of 30t was moved 6.0 m transvesly causing a 30 cm deflection in a 6m pendulum, calculate the transverse meta centre height.arrow_forwarda ship 150 m long and 20.5 m beam floats at a draught of8 m and displaces 19 500 tonne. The TPC is 26.5 and midshipsection area coefficient 0.94. Calculate the block, prismatic andwaterplane area coefficients.arrow_forward
- A vessel loads 680 t fuel between forward and aft deep tanks. centre of gravity of forward tank is 24m forward of ships COG. centre to centre between tanks is 42 m. how much in each tank to keep trim the samearrow_forwardBeam of a vessel is 11% its length. Cw =0.72. When floating in SW of relative denisity 1.03, TPC is 0.35t greater than in freshwater. Find the length of the shiparrow_forwardAn inclining experiment was carried out on a ship of 4000tonne displacement, when masses of 6 tonne were moved transverselythrough 13.5 m. The deflections of a 7.5 m pendulurnwere 81, 78, 85, 83, 79, 82, 84 and 80 mm respectively.Caiculate the metacentric height.arrow_forward
- A ship of 10 000 tonne displacement has a waterplanearea of 1300 m2. The ship loads in water of 1.010 t/m3 andmoves into water of 1.026 t/m3. Find the change in meandraughtarrow_forwardA ship of 7000 tonne displacement has a waterplane areaof 1500 m2. In passing from sea water into river water of1005 kg/m3 there is an increase in draught of 10 cm. Find the Idensity of the sea water.arrow_forwardA ship has 300 tonne of cargo in the hold, 24 m forward ofmidships. The displacement of the vessel is 6000 tonne and its centre of gravity is 1.2 m forward of midships.Find the new position of the centre of gravity if this cargo ismoved to an after hold, 40 m from midshipsarrow_forward
- Sketch and describe how ships are supported in dry dock. When and where does the greatest amount of stresses occur?arrow_forwardSketch and desribe a balanced rudder and how it is suspendedarrow_forwardA ship 140 m long and 18 m beam floats at a draught of9 m. The immersed cross-sectionai areas at equai intervais are 5,60, 116, 145, 152, 153, 153, 151, 142, 85 and 0 m2 respectively.Calculate:(a) displacement(b) block coefficient(c) midship section area coefficient(d) prismatic coefficient.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License