Concept explainers
Find the amount of natural gas required in
Answer to Problem 19P
The amount of natural gas required in
Explanation of Solution
Given data:
Refer to problem 13-19 accompanying table in the textbook.
The average efficiency of the power plant is 35%.
The heating value of the natural gas is
Formula used:
Formula to calculate the power plant efficiency is,
Rearrange the equation,
Convert Btu to
Convert
The value of the
Convert 1 hr into seconds,
Rearrange the equation,
Substitute equation (5) in equation (4),
Rearrange the equation,
Calculation:
Converting the given data from kWh to Btu:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Now find the energy input fuel for each year in Btu for natural gas:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Now convert Btu to lbm as follows by using the relation
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Now convert Form lbm to
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Therefore, the amount of natural gas in
Conclusion:
Hence, the amount of natural gas in
Want to see more full solutions like this?
Chapter 13 Solutions
Engineering Fundamentals: An Introduction to Engineering
- Determine the energy consumption (BTU/min), If two 50-kg LPG tanks are needed per 24-hour operation, heating value for the LPG of 11,000 kcal/kg. Subject: Civil Engineering: Thermodynamicsarrow_forwardAn average American consumes approximately 105 kJ of energy per day. The average life expectancy of an American is 77.9 years. How much coal would need to be burned to provide enough energy to meet a person's energy demands if the efficiency of energy production from coal is 38%? ☐g coalarrow_forwardWater falls from a height of 500 m and the mass of water is 50 kg. What is approximately the rise in temperature of water at the bottom if the whole energy is used to heat the water? Specific heat of water is 4.18 kJ/kg-deg C. O 5000 deg C O 1173 deg C O 500 deg C O 0.23 deg C O none of the abovearrow_forward
- For a building located in London, England with annual heating degree-days (dd) of 5634, a heating load (heat loss) of 42,000 kj/h, and a design temperature difference of 35° C (20° C indoor), estimate the annual energy consumption. If the building is heated with a furnace with an efficiency of 98%, how much gas is burned to keep the home at 20° C? State yourassumptions.arrow_forwardConclusion about total energies, EDF ( energie de france) and EDP ( energis de Portugal) in 2021 ?arrow_forwardA heat pump supplies heat energy to a house at the rate of 140,000 kJ/h when the house is maintained at 25°C. Over a period of one month, the heat pump operates for 100 hours to transfer energy from a heat source outside the house to inside the house. Consider a heat pump receiving heat from two different outside energy sources. In one application the heat pump receives heat from the outside air at 0°C. In a second application the heat pump receives heat from a lake having a water temperature of 10°C. If electricity costs $0.105/kWh, determine the maximum money saved by using the lake water rather than the outside air as the outside energy source.arrow_forward
- Answers are given! please explain the steps of the full solution! ASAP Energy density of hydrogen in a 700bar tank is 5MJ/KG.arrow_forward2. Consider the system described in the news: at night, when there is energy left, water is pumped from a large lake to a reservoir at 80 m above the lake level. During the day, this water is used to generate energy in a turbine located 80 m below the elevated reservoir. Considering that the water flow is always 5000 liters/s (both at the inlet of the reservoir and at the outlet) and that the pump and turbine efficiencies are 70%, what is the power (in kW) required by the pump and the power (in kW) recovered in the turbine. Data: The pipe diameter is always the same along the system (d = 0.5 m); g = 10 m/s2; γ = 9810 N/m3. Matter transport phenomena; Please make it typeable as handwriting interferes with understandingarrow_forwardA 600 MW coal-fired power plant has an overall thermal efficiency of 38%. It is burning coal that has a heating value of 12,000 Btu/lb, an ash content of 5%, a sulfur content of 3,0%, and a CO2 emission factor of 220 IWmillion Bin. Calculate the heat emitted to the environment (Btu/sec), the coal feed rate (tons/day), the degree (%) of sulfur dioxide control needed to meet an emission standard of 0,15 lh SO2/inillion Bin of heat input, and the CO2 emission rate (metric tons/day).arrow_forward
- The Energy Efficiency Rating (EER) of an air-conditioning unit is defined asthe ratio of the heat removed in Btu/h divided by the energy used in watts.The EEI (Edison Electric Institute) names an air-conditioning unit as anEnergy Star unit if it has an EER of 13 or greater. A 21⁄2-ton air-conditioningunit uses 2.41 kilowatts (2,410 watts) of energy. One ton is equivalent to12,000 Btu/h. Can this unit be termed an Energy Star unit?arrow_forwardSolve via mechanical energy balance equationarrow_forwardQ1: What is the primary process of converting solar energy into other form of energy, explain and give an example of each one of them? Q2: Determine the Sun's altitude angle , azimuth angle, and zenith angle at 5.00 P.M on December 15, 2017 for a location at 24.85° N latitude. Q3: Compare the power generated by the two shown systems 1 and 2, if each turbine have air velocity in that area was V= 5 m/sec and the air density p=1.19 kg/m³m while in system 2 to increase the air velocity we uses a truncated cone of area ration A1/A2=4. blades 5 m length, while thearrow_forward
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning