Concept explainers
(a)
Interpretation:
To interpret the value of temperature of gas with the help of ideal gas equation.
Concept Introduction:
The pressure, volume and temperature for ideal gas can be calculated with the help of ideal gas. The ideal gas equation is as given below:
PV = nRT
Here R is gas constant that value is 0.0821 L. atm / K. mol.
(b)
Interpretation:
To interpret the value of pressure of gas with the help of ideal gas equation.
Concept Introduction:
The pressure, volume and temperature for ideal gas can be calculated with the help of ideal gas. The ideal gas equation is as given below:
PV = nRT
Here R is gas constant that value is 0.0821 L. atm / K. mol.
(c)
Interpretation:
To interpret the value of volume of gas with the help of ideal gas equation.
Concept Introduction:
The pressure, volume and temperature for ideal gas can be calculated with the help of ideal gas. The ideal gas equation is as given below:
PV = nRT
Here R is gas constant that value is 0.0821 L. atm / K. mol.
Want to see the full answer?
Check out a sample textbook solutionChapter 13 Solutions
Bundle: Introductory Chemistry: A Foundation, Loose-leaf Version, 9th + OWLv2 with MindTap Reader, 1 term (6 months) Printed Access Card
- 5-107 If 60.0 g of NH3 occupies 35.1 L under a pressure of 77.2 in. Hg, what is the temperature of the gas, in °C?arrow_forwardA four-liter tank is filled with propane gas, C3H8. The mass of the tank filled with gas is 1236 g. The pressure in the tank is 2.68 atm. The temperature in the room is 37C. The propane in the tank is used up under the same conditions of temperature and pressure. What is the mass of the empty tank?arrow_forwardA typical barometric pressure in Redding. California, is about 750 mm Hg. Calculate this pressure in atm and kPa.arrow_forward
- perform stoichiometric ca1cu1uions for reactions involving gases as reactants or products.arrow_forwardA 1.000-g sample of an unknown gas at 0C gives the following data: P(atm) V (L) 0.2500 3.1908 0.5000 1.5928 0.7500 1.0601 1.0000 0.7930 Use these data to calculate the value of the molar mass at each of the given pressures from the ideal gas law (we will call this the apparent molar mass at this pressure). Plot the apparent molar masses against pressure and extrapolate to find the molar mass at zero pressure. Because the ideal gas law is most accurate at low pressures, this extrapolation will give an accurate value for the molar mass. What is the accurate molar mass?arrow_forwardPressures of gases in mixtures are referred to as partial pressures and are additive. 1.00 L of He gas at 0.75 atm is mixed with 2.00 L of Ne gas at 1.5 atm at a temperature of 25.0 C to make a total volume of 3.00 L of a mixture. Assuming no temperature change and that He and Ne can be approximated as ideal gases, what are a the total resulting pressure, b the partial pressures of each component, and c the mole fractions of each gas in the mix?arrow_forward
- 93 The complete combustion of octane can be used as a model for the burning of gasoline: 2C8H18+25O216CO2+18H2O Assuming that this equation provides a reasonable model of the actual combustion process, what volume of air at 1.0 atm and 25°C must be taken into an engine to burn 1 gallon of gasoline? (The partial pressure of oxygen in air is 0.21 atm and the density of liquid octane is 0.70 g/mL.)arrow_forwardYou have a gas, one of the three known phosphorus-fluorine compounds (PF3, PF3, and P2F4). To find out which, you have decided to measure its molar mass. (a) First, yon determine that the density of the gas is 5.60 g/L at a pressure of 0.971 atm and a temperature of 18.2 C. Calculate the molar mass and identify the compound. (b) To check the results from part (a), you decide to measure the molar mass based on the relative rales of effusion of the unknown gas and CO2. You find that CO2 effuses at a rate of 0.050 mol/min, whereas the unknown phosphorus fluoride effuses at a rate of 0.028 mol/min. Calculate the molar mass of the unknown gas based on these results.arrow_forwardExplain why the plot of PV for CO2 differs from that of an ideal gas.arrow_forward
- In the Mthode Champenoise, grape juice is fermented in a wine bottle to produce sparkling wine. The reaction is C6H12O6(aq)2C2H5OH(aq)+2CO2(g) Fermentation of 750. mL grape juice (density = 1.0 g/cm3) is allowed to take place in a bottle with a total volume of 825 mL until 12% by volume is ethanol (C2H5OH). Assuming that the CO2 is insoluble in H2O (actually, a wrong assumption), what would be the pressure of CO2 inside the wine bottle at 25C? (The density of ethanol is 0.79 g/cm3.)arrow_forwardA cylinder of compressed gas is labeled Composition (mole %): 4.5% H2S, 3.0% CO2, balance N2. The pressure gauge attached to the cylinder reads 46 atm. Calculate the partial pressure of each gas, in atmospheres, in the cylinder.arrow_forward61 As one step in its purification, nickel metal reacts with carbon monoxide to form a compound called nickel tetracarbonyl, Ni(CO)4, which is a gas at temperature above about 316 K. A 2.000-L flask is filled with CO gas to a pressure of 748 torr at 350.0 K, and then 5.00 g of Ni is added. If the reaction describe occurs and goes to completion at constant temperature, what will the final pressure in the falsk be?arrow_forward
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistry: An Atoms First ApproachChemistryISBN:9781305079243Author:Steven S. Zumdahl, Susan A. ZumdahlPublisher:Cengage Learning
- Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage LearningWorld of Chemistry, 3rd editionChemistryISBN:9781133109655Author:Steven S. Zumdahl, Susan L. Zumdahl, Donald J. DeCostePublisher:Brooks / Cole / Cengage LearningChemistry for Engineering StudentsChemistryISBN:9781337398909Author:Lawrence S. Brown, Tom HolmePublisher:Cengage Learning