Explanation Given information: The applied force at end A of the bracket ( P ) is 8 kip . The flexural rigidity of the bracket is E I . The length of the bracket ( L ) is 3 in . . Calculation: Consider that the deflection is small enough so that the force 8 kip remains in line with segment AB and then bending of segment of AB can be neglected. Show the free body diagram of the bracket as in Figure 1. Refer to Figure 1. Calculate the vertical displacement at the end A of the bracket ( υ A ) using the formula: υ A = P L 3 3 E I (1) Substitute 8 kip for P and 3 in . for L in Equation (1)

Mechanics of Materials Plus Mastering Engineering with Pearson eText - Access Card Package (10th Edition)

10th Edition

ISBN: 9780134518121

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and af…

Videos

Question

Chapter 12.5, Problem 12.94P

To determine

The vertical displacement at the end A of the bracket (υA).

The change in angle at the end A of the bracket (θA).

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 12.5, Problem 12.93P

Chapter 12.5, Problem 12.95P

Students have asked these similar questions

3. An engine has three cylinders spaced at 120° to each other. The crank torque diagram can be simplified to a triangle having the following values: Angle 0° Torque (Nm) 0 (a) What is the mean torque? 60° 4500 180° 180° to 360° 0 0 (b) What moment of inertia of flywheel is required to keep the speed to within 180 ± 3 rpm? (c) If one cylinder of the engine is made inoperative and it is assumed that the torque for this cylinder is zero for all crank angles, determine the fluctuation in speed at 180rpm for the same flywheel. (a) 3375 Nm (b) 50kgm (c) ±21 rpm

Prob 5. Determine the largest load P that can be applied to the frame without causing either the average normal stress or the average shear stress at section a-a to exceed o-150 MPa and 1-60 MPa, respectively. Member CB has a square cross section of 25 mm on each side. 2 m FAC 1.5 m Fac

Derive the component transformation equations for tensors shown below where [C] = [BA] is the DCM (direction cosine matrix) from frame A to B. ^B [T] = [C]^A [T] [C]^T

Chapter 12 Solutions

Mechanics of Materials Plus Mastering Engineering with Pearson eText - Access Card Package (10th Edition)

Ch. 12.2 - In each case, determine the internal bending...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope of end A of the cantilevered...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the slope of the simply supported beam...Ch. 12.2 - An L2 steel strap having a thickness of 0.125 in....Ch. 12.2 - The L2 steel blade of the band saw wraps around...Ch. 12.2 - A picture is taken of a man performing a pole...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The vertical displacement at the end A of the bracket ( υ A ) . The change in angle at the end A of the bracket ( θ A ) .

Solution Summary: The author calculates the vertical displacement at the end A of the bracket (upsilon_A) using the formula:

Concept explainers

Videos

The vertical displacement at the end A of the bracket (υA).

The change in angle at the end A of the bracket (θA).

Want to see the full answer?

Chapter 12 Solutions

The vertical displacement at the end A of the bracket ( υ A ) . The change in angle at the end A of the bracket ( θ A ) .

Solution Summary: The author calculates the vertical displacement at the end A of the bracket (upsilon_A) using the formula:

Concept explainers

Videos

The vertical displacement at the end A of the bracket (υA). The change in angle at the end A of the bracket (θA).

Want to see the full answer?

Chapter 12 Solutions

The vertical displacement at the end A of the bracket (υA).

The change in angle at the end A of the bracket (θA).