Explanation Given information: The load act at the first pulley ( P 1 ) is 50 lb . The load act at the second pulley ( P 2 ) is 80 lb . The flexural rigidity of the shaft is E I . The length of the shaft ( L ) is 60 in . Calculation: Show the free body diagram of the shaft as in Figure 1. Refer to Figure 1. Calculate the support reactions A and B ( R A and R B ) : Calculate the vertical forces by applying the equation of equilibrium: Sum of vertical forces is equal to 0. ∑ F y = 0 R A + R B − 50 − 80 = 0 R A + R B = 130 (1) Calculate the moment about point A by applying the equation of equilibrium: Sum of moments about point A is equal to 0. ∑ M A = 0 ( R B × 48 ) − ( 80 × 24 ) + ( 50 × 12 ) = 0 48 R B − 1 , 320 = 0 48 R B = 1 , 320 R B = 1 , 320 48 R B = − 27.5 lb R B = 27.5 lb ( ↓ ) Substitute 27.5 lb for R B in Equation (1). R A + 27.5 = 130 R A = 130 − 27.5 R A = 102.5 lb Calculate the moment function with respect of the x distance M ( x ) : M ( x ) = − 50 ( x − 0 ) − ( − 102.5 ) ( x − 12 ) − 80 ( x − 36 ) = − 50 x + 102.5 ( x − 12 ) − 80 ( x − 36 ) Elastic Curve and slope is as follows: E I d 2 υ d x 2 = M ( x ) (2) Substitute [ − 50 x + 102.5 ( x − 12 ) − 80 ( x − 36 ) ] for M ( x ) in Equation (2). E I d 2 υ d x 2 = − 50 x + 102.5 ( x − 12 ) − 80 ( x − 36 ) (3) Integrate both sides of the Equation (3). E I d υ d x = − 50 x 2 2 + 102.5 2 ( x − 12 ) 2 − 80 2 ( x − 36 ) 2 + C 1 = − 25 x 2 + 102.5 2 ( x − 12 ) 2 − 40 ( x − 36 ) 2 + C 1 (4) Integrate both sides of the Equation (4). E I υ = − 25 x 3 3 + 102.5 3 ( x − 12 ) 3 − 40 3 ( x − 36 ) 3 + C 1 x + C 2 = [ − 25 3 x 3 + 102.5 6 ( x − 12 ) 3 − 40 3 ( x − 36 ) 3 + C 1 x + C 2 ] (5) Boundary conditions are as follows: υ = 0 at x = 12 in . υ = 0 at x = 60 in

Mechanics of Materials Plus Mastering Engineering with Pearson eText - Access Card Package (10th Edition)

10th Edition

ISBN: 9780134518121

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft …

Question

Chapter 12.3, Problem 12.42P

To determine

The slop at A(θA).

The slop at B(θB).

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 12.3, Problem 12.41P

Chapter 12.3, Problem 12.43P

Students have asked these similar questions

Calculate for the vertical cross section moment of inertia for both Orientations 1 and 2 of a 1 x 1.5 in. horizontal hollow rectangular beam with wall thickness of t = 0.0625 in. Use the equation: I = ((bh^3)/12) - (((b-2t)(h-2t)^3)/12)

Please answer 'yes' or 'no' and 'is' or 'is not' for the following:

Consider a large 23-cm-thick stainless steel plate (k = 15.1 W/m-K) in which heat is generated uniformly at a rate of 5 x 105 W/m³. Both sides of the plate are exposed to an environment at 30°C with a heat transfer coefficient of 60 W/m²K. The highest temperature will occur at surfaces of plate while the lowest temperature will occur at the midplane. Yes or No Yes No

Chapter 12 Solutions

Mechanics of Materials Plus Mastering Engineering with Pearson eText - Access Card Package (10th Edition)

Ch. 12.2 - In each case, determine the internal bending...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope of end A of the cantilevered...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the slope of the simply supported beam...Ch. 12.2 - An L2 steel strap having a thickness of 0.125 in....Ch. 12.2 - The L2 steel blade of the band saw wraps around...Ch. 12.2 - A picture is taken of a man performing a pole...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The slop at A ( θ A ) . The slop at B ( θ B ) .

Solution Summary: The author calculates the slop at A and B by applying the equation of equilibrium: Sum of moments about point A is equal to 0.

Concept explainers

The slop at A(θA).

The slop at B(θB).

Want to see the full answer?

Chapter 12 Solutions

The slop at A ( θ A ) . The slop at B ( θ B ) .

Solution Summary: The author calculates the slop at A and B by applying the equation of equilibrium: Sum of moments about point A is equal to 0.

Concept explainers

The slop at A(θA). The slop at B(θB).

Want to see the full answer?

Chapter 12 Solutions

The slop at A(θA).

The slop at B(θB).