Explanation Given information: The uniformly distributed load act at a distance from left end of the beam is w . The point load act at right end of the beam is P . The flexural rigidity of the beam is E I . The length of the beam ( L ) is 2 a . Calculation: Show the free bodydiagram of the beam as in Figure 1. Refer to Figure 1. Calculate the vertical forces by applying the Equation of equilibrium: Sum of vertical forces is equal to 0. ∑ F y = 0 R A − ( w × a ) − P = 0 R A − w a − P = 0 R A = w a + P Calculate the moment about point A by applying the Equation of equilibrium: Sum of moments about point A is equal to 0. ∑ M A = 0 M A − ( w × a × a 2 ) − ( P × 2 a ) = 0 M A − w a 2 2 − 2 P a = 0 M A = w a 2 2 + 2 P a Show the moment area diagramsfor the point load and uniformly distributed load of the beam as in Figure 2. Refer to Figure 2. Show the bending monument calculation follows: Calculate the bending moment at A ( M A ) u for uniformly distributed load: ( M A ) u = − ( w × a × a 2 ) = − w a 2 2 Calculate the bending moment at A ( M A ) p for point load: ( M A ) p = − ( P × 2 a ) = − 2 P a Calculate the bending moment at B ( M B ) u for uniformly distributed load: ( M B ) u = − ( w × 0 × 0 2 ) = 0 Calculate the bending moment at B ( M B ) p for point load: ( M B ) p = − ( P × a ) = − P a Calculate the bending moment at C : M C = ( P × 0 ) = 0 Show the deflected shape of the shaft as in Figure 3. Refer to Figure 3. The support at A is fixed. Therefore, the slope at A ( θ A ) is 0

10th Edition

ISBN: 9780134321158

Author: HIBBELER

Publisher: PEARSON

See similar textbooks

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and af…

Videos

Question

Chapter 12.4, Problem 12.79P

To determine

The slope at C(θC).

The deflection at C(υC).

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 12.4, Problem 12.78P

Chapter 12.4, Problem 12.80P

Students have asked these similar questions

Determine the Mean Effective Pressure (MEP) in [bar] for a 4-cylinder, 2-Stroke engine with a bore of 85.7 mm, and a stroke of 65.8 mm, that produces 85 hP at 5000 rpm. (Hint: Be careful with units). Note: 1 hP = 0.7457 kW; 100 kPa = 1 bar

Ibraheem Super Q3: A boiler as shown in the figure below is producing 2 kg/s saturated steam at 240C. The water enters the boiler at 24C. The boiler efficiency is 80%. Patm=1.05 bar .Determine: (10 Marks) 1- The inlet pressure of the turbine. 2- If a gauge pressure connected to the outlet pipe, what is the reading of this gauge? 3- Calculate the required diesel in [kg/s]. Assume the calorific value of the diesel is 45000 kJ/kgf 4- Calculate the equivalent evaporation of the boiler 5- Keeping the same inlet conditions and fuel consumption, determine the turbine efficiency if the produced steam was saturated at 300C. Steam Cut Hot Gasses Out Ts=240C Boiler FURNACE A Water In C 24 Examiner Head of Department Ahmad. A. M. Alsak lani

##2# Superheated steam powers a steam turbine for the production of electrical energy. The steam expands in the turbine and at an intermediate expansion pressure (0.1 Mpa) a fraction is extracted for a regeneration process in a surface regenerator. The turbine has an isentropic efficiency of 90% Design the simplified power plant schematic Analyze it on the basis of the attached figure Determine the power generated and the thermal efficiency of the plant ### Dados in the attached images

Chapter 12 Solutions

Mechanics of Materials

Ch. 12.2 - In each case, determine the internal bending...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope of end A of the cantilevered...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the slope of the simply supported beam...Ch. 12.2 - An L2 steel strap having a thickness of 0.125 in....Ch. 12.2 - The L2 steel blade of the band saw wraps around...Ch. 12.2 - A picture is taken of a man performing a pole...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.