The error that has been made by student in the setup should be determined. Concept introduction: Distillation is a liquid-gas separation technique for two or more liquids on the basis of their difference in boiling temperature or vapor pressure.Vapor pressure is pressure exerted by vapor phase of liquid produced due to an increase in the molecular kinetic energy of the liquid phase or due to the increase in temperature. The temperature at which atmospheric pressure exerted on liquid equals to its vapor pressure is known to be its boiling point. Vapor pressure of the component decide boiling point of any mixture. Impurities in the mixture might result in an increase or decrease of observed boiling temperature. The steps for distillation are as follows: In distillation, a round bottom flask is filled one-third or half full with the liquid compound to be distilled. If the flask is overfilled it might flow inside condenser attached to it. Then a distilling head is inserted into the round bottom flask and then a condenser is attached to the side joint of the distilling head from where the compound is collected in another smaller round bottom flask after distillation. A heat source is placed below the distillation flask. A thermometer is carefully inserted in the thermometer adaptor and is placed properly on the distillation head for measuring the boiling temperature of the compound being distilled.

Question

Want to see the full answer?

Answer 1

Question

Chapter 12, Problem 3Q

Interpretation Introduction

Interpretation:

The error that has been made by student in the setup should be determined.

Concept introduction:

Distillation is a liquid-gas separation technique for two or more liquids on the basis of their difference in boiling temperature or vapor pressure.Vapor pressure is pressure exerted by vapor phase of liquid produced due to an increase in the molecular kinetic energy of the liquid phase or due to the increase in temperature.

The temperature at which atmospheric pressure exerted on liquid equals to its vapor pressure is known to be its boiling point. Vapor pressure of the component decide boiling point of any mixture. Impurities in the mixture might result in an increase or decrease of observed boiling temperature.

The steps for distillation are as follows:

In distillation, a round bottom flask is filled one-third or half full with the liquid compound to be distilled. If the flask is overfilled it might flow inside condenser attached to it.

Then a distilling head is inserted into the round bottom flask and then a condenser is attached to the side joint of the distilling head from where the compound is collected in another smaller round bottom flask after distillation.

A heat source is placed below the distillation flask.

A thermometer is carefully inserted in the thermometer adaptor and is placed properly on the distillation head for measuring the boiling temperature of the compound being distilled.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

О δα HO- H -Br δα HO-- + + -Br [B] 8+ HO- -Br δα न

1/2 - 51% + » GAY Organic Reactions Assignment /26 Write the type of reaction that is occurring on the line provided then complete the reaction. Only include the major products and any byproducts (e.g. H₂O) but no minor products. Please use either full structural diagrams or the combination method shown in the lesson. Skeletal/line diagrams will not be accepted. H3C 1. 2. CH3 A Acid OH Type of Reaction: NH Type of Reaction: + H₂O Catalyst + HBr 3. Type of Reaction: H3C 4. Type Reaction: 5. H3C CH2 + H2O OH + [0] CH3 Type of Reaction: 6. OH CH3 HO CH3 + Type of Reaction: 7. Type of Reaction: + [H]

humbnai Concentration Terms[1].pdf ox + New Home Edit Sign in Comment Convert Page Fill & Sign Protect Tools Batch +WPS A Free Trial Share Inter Concreting Concentration forms. Hydrogen peroxide is a powerful oxidizing agent wed in concentrated solution in rocket fuels and in dilute solution as a hair bleach. An aqueous sulation of H2O2 is 30% by mass and has density of #liligime calculat the Ⓒmolality ⑥mole fraction of molarity. 20 9. B. A sample of Commercial Concentrated hydrochloric ET