The property consistent with given types of solid has to be identified. Concept introduction: Metallic solid: Metallic solid is high melting points, range from soft and malleable to very hard, which are good conductors of electricity. Ionic solid: Ionic solid has very high melting points Ionic solids are brittleness and poor conductors in the solid state. Molecular solid: Molecular solids melt closer to 300 °C, which is can be either ductile or brittle. Many molecular solids have a large band gap between the valence band and conduction band. Network solid: Network solid has very high melting point, which are very hard. Network solid doesn't conduct electricity, which are insoluble in water and organic solvents. Amorphous solid: In these solids particles are randomly arranged in three dimensions, does not have sharp melting points, which forms due to sudden cooling of liquid. Alloy solid: Alloy solid is high melting points, which are good conductors of electricity.

Question

Want to see the full answer?

Answer 1

Question

Chapter 12, Problem 28PS

Interpretation Introduction

Interpretation:

The property consistent with given types of solid has to be identified.

Concept introduction:

Metallic solid:

Metallic solid is high melting points, range from soft and malleable to very hard, which are good conductors of electricity.

Ionic solid:

Ionic solid has very high melting points

Ionic solids are brittleness and poor conductors in the solid state.

Molecular solid:

Molecular solids melt closer to 300 °C, which is can be either ductile or brittle. Many molecular solids have a large band gap between the valence band and conduction band.

Network solid:

Network solid has very high melting point, which are very hard.

Network solid doesn't conduct electricity, which are insoluble in water and organic solvents.

Amorphous solid:

In these solids particles are randomly arranged in three dimensions, does not have sharp melting points, which forms due to sudden cooling of liquid.

Alloy solid:

Alloy solid is high melting points, which are good conductors of electricity.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

9. OA. Rank the expected boiling points of the compounds shown below from highest to lowest. Place your answer appropriately in the box. Only the answer in the box will be graded. (3) points) OH OH بر بد بدید 2 3

There is an instrument in Johnson 334 that measures total-reflectance x-ray fluorescence (TXRF) to do elemental analysis (i.e., determine what elements are present in a sample). A researcher is preparing a to measure calcium content in a series of well water samples by TXRF with an internal standard of vanadium (atomic symbol: V). She has prepared a series of standard solutions to ensure a linear instrument response over the expected Ca concentration range of 40-80 ppm. The concentrations of Ca and V (ppm) and the instrument response (peak area, arbitrary units) are shown below. Also included is a sample spectrum. Equation 1 describes the response factor, K, relating the analyte signal (SA) and the standard signal (SIS) to their respective concentrations (CA and CIS). Ca, ppm V, ppm SCa, arb. units SV, arb. units 20.0 10.0 14375.11 14261.02 40.0 10.0 36182.15 17997.10 60.0 10.0 39275.74 12988.01 80.0 10.0 57530.75 14268.54 100.0…

A mixture of 0.568 M H₂O, 0.438 M Cl₂O, and 0.710 M HClO are enclosed in a vessel at 25 °C. H₂O(g) + C₁₂O(g) = 2 HOCl(g) K = 0.0900 at 25°C с Calculate the equilibrium concentrations of each gas at 25 °C. [H₂O]= [C₁₂O]= [HOCI]= M Σ M