Fundamentals of Aerodynamics
6th Edition
ISBN: 9781259129919
Author: John D. Anderson Jr.
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 12.4P
Equation
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
How do we use the Buckingham pi theorem to prove that drag coefficient is dimensionless?
A model of a jet fighter aircraft of the military is to be tested in a pressurized helium wind tunnel to identify the effects of flying at supersonic speeds. Which of the following is the primary
criterion to be satisfied such that the model and prototype are dynamically similar?
Select one:
O a. Reynolds Law
O b. Mach Law
О с. Froude Law
O d. Weber Law
Consider a solid iron sphere entering the earth's atmosphere at 13 km/s (slightly above es-
cape velocity) and at an angle of 15° below the local horizontal. The sphere diameter is
1 m. The drag coefficient for a sphere at hypersonic speeds is approximately 1. The den-
sity of iron is 6963 kg/m³. Calculate (a) the altitude at which maximum deceleration oc-
curs, (b) the value of the maximum deceleration, and (c) the velocity at which the sphere
would impact the earth's surface.
Chapter 12 Solutions
Fundamentals of Aerodynamics
Ch. 12 - Using the results of linearized theory, calculate...Ch. 12 - For the conditions of Problem 12.1, calculate the...Ch. 12 - Consider a diamond-wedge airfoil such as shown in...Ch. 12 - Equation (12.24). from linear supersonic theory....Ch. 12 - Consider a flat plate at an angle of attack in an...Ch. 12 - Consider a flat plate at an angle of attack in a...Ch. 12 - Using the same flight conditions and the same...Ch. 12 - The result from Problem 12.6 demonstrates that...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.arrow_forwardI need the answer as soon as possiblearrow_forwardA wind tunnel is being used to study the aerodynamics of a full-scale model rocket that is 30 cm long. Scaling for drag calculations are based on the Reynolds number. The rocket hasan expected maximum velocity of 190 km/h. What is the Reynolds number at this speed? Assume ambient air is at 20°C. The wind tunnel is capable of speeds up to 160 km/h; so an attempt is made to improve this top speed by varying the air temperature. Calculate the equivalent speed for the wind tunnel using air at 5°C and 65°C. Would replacing air with carbon dioxide provide higher equivalent speeds?arrow_forward
- A 2 m diameter cylinder rotates at 1800 rpm in an air stream (p=1226 kg/m³) of 25 m/sec. Estimate the theoretical lift per unit length of the cylinder (in Newtons) Ajoarrow_forwardQ4-Q6: A device is used to cool hot copper spheres of diameter 5 mm from an average temperature of 200C to 50C by letting them fall in air at 25°C and latm. Use drag coefficient C, = 0.4 and Whitaker correlation in your calculations. Assume the spheres fall at their terminal velocities during the process. Q4 improve the accuracy? Iteration is not required. ) Determine the terminal velocity of a sphere. Is the use of C, = 0.4 appropriate? If not, how toarrow_forwardA 1:20 scaled-down model of a hydrofoil is tested in a water channel, at a velocity of 0.179 m/s. At this velocity, a drag force of 2.2 N is measured. Determine the drag force of the original hydrofoil, at a velocity of 0.8 m/s.arrow_forward
- The 2013 Toyota Camry has an empty weight of 3190 lbf, a frontal area of 22.06 ft2, and a drag coefficient of 0.28. Its rolling resistance is Crr ≈ 0.035. Estimate the maximum velocity, in mi/h, this car can attain when rolling freely at sea level down a 4° slope.arrow_forwardParrow_forward2. A 1500 kg electric vehicle travels along an asphalt roadway with a 5° grade at 100 km/h and a rolling resistance coefficient of 0.013. The frontal area is 2.05 m² and a drag coefficient is 0.32. The battery capacity is 85kWh and the battery nominal voltage is 320V. The air density of 1.2 kg/m3. (a) What is the power required to propel this vehicle? (b) The gear ratio is 10.7, the tire radius is 0.23m. Assume 100% efficiency for the gear. (i) What is the torque seen by the ac propulsion motor (ii) What is the power and speed of the motor? (c) What is the range of the vehicle considering 80% Depth of Discharge on a flat road at a speed of 50 km/h? 3. In the system of problem 2, the propulsion motor used is a star connected interior permanent magnet motor fed by a three phase IGBT inverter. The motor is operated in direct torque controlled mode. The inverter output voltage is 414V(L-L) and the modulation index is 0.9. The motor efficiency is 98% and power factor is 0.78. The dc link…arrow_forward
- Consider a business jet with the following characteristics:• Weight: 25208 kg• Wing area: 53.5 m^2• Wing span: 21.7 m• Cruise altitude: 10,000 m • Drag polar parameters (cruise): CD0 = 0.015, K= 0.08• Engine: Number of engines: 2 Max. thrust (at sea level, for 1 engine): 45 kN TSFC (for 1 engine): 0.41 1/h Calculate the velocity for minimum thrust required using the analytical expression (formula)? Calculate the velocity for minimum power required using the analytical expression (formula).? Calculate the maximum velocity using one possible graphical approach, and analytical approach?arrow_forwardNonearrow_forwardEstimate the annual production of a 12 m diameter horizontal axis wind turbine operating atstandard atmospheric conditions (r = 1.225 kg/m3 ) in an 8 m/s average wind speed regime. speed probality density is given by the Rayleigh density distribution.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License