Explanation Write the given equation of state. v = R T p + B − A R T Partially differentiate the equation of state with respect to temperature by keeping the pressure as constant. ( ∂ v ∂ T ) p = R p + A R T 2 (I) Here, the change in the specific volume with respect to change in the temperature at constant pressure is ( ∂ v ∂ T ) p . the specific volume is v , the gas constant is R , the temperature is T , the pressure of the gas is p and the constant are A and B . Write the expression for change in entropy. s ( p 2 , T ) − s ( p 1 , T ) = − ∫ p 1 p 2 ( ∂ v ∂ T ) p d p (II) Here, the specific entropy at state 2 is s ( p 2 , T ) , the specific entropy at state 1 is s ( p 1 , T ) , the final pressure is p 2 and the initial pressure is p 1 . Write the expression for the change in enthalpy. h ( p 2 , T ) − h ( p 1 , T ) = ∫ p 1 p 2 ( v − T ( ∂ v ∂ T ) p ) d p (III) Here, the specific enthalpy at state 2 is h ( p 2 , T ) and the specific enthalpy at state 1 is h ( p 1 , T ) . Write the expression for difference in the specific enthalpy. h ( p 2 , T ) − h ( p 1 , T ) = u ( p 2 , T ) − u ( p 1 , T ) − ( p 2 v 2 − p 1 v 1 ) (IV) Here, the change in internal energy at state 1 is u ( p 2 , T ) , the change in internal energy at state 2 is u ( p 1 , T ) , the change in specific enthalpy at state 1 is h ( p 2 , T ) and the change in specific at state 2 is u ( p 1 , T ) . Conclusion: Substitute R p + A R T 2 for ( ∂ v ∂ T ) p in the Equation (II). s ( p 2 , T ) − s ( p 1 , T ) = − ∫ p 1 p 2 ( R p + A R T 2 ) d p = − R ln ( p 2 p 1 ) − A R T 2 ( p 2 − p 1 ) Thus, the expression for entropy change is s ( p 2 , T ) − s ( p 1 , T ) = − R ln ( p 2 p 1 ) − A R T 2 ( p 2 − p 1 )

Fundamentals of Engineering Thermodynamics

8th Edition

ISBN: 9781118832301

Author: SHAPIRO

Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT

See similar textbooks

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its m…

Videos

Question

Chapter 11.9, Problem 48P

To determine

The expression for the change in specific enthalpy.

The expression for the change in internal energy.

The expression for the change in the entropy

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11.9, Problem 47P

Chapter 11.9, Problem 49P

Students have asked these similar questions

Hints: Find the closed loop transfer function and then plot the step response for diFerentvalues of K in MATLAB. Show step response plot for different values of K. Auto Controls Show solutions and provide matlab code NO COPIED ANSWERS OR WILL REPORT!!!!

37. The vertical shaft shown in Figure P12-37 is driven at a speed of 600 rpm with 4.0 hp entering through the bevel gear. Each of the two chain sprockets delivers 2.0 hp to the side to drive mixer blades in a chemical reactor vessel. The bevel gear has a diametral pitch of 5, a pitch diameter of 9.000 in, a face width of 1.31 in, and a pressure angle of 20°. Use SAE 4140 OQT 1000 steel for the shaft. See Chapter 10 for the methods for computing the forces on the bevel gear. Figure P12-37: P37-Bevel gear drive with two chain sprockets Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of strength. Homework Problems 12-24, 12-35, and 12-37 from textbook, done in spreadsheet form. Place drawings of the load, shear, and bending moment body diagrams…

35. The double-reduction, helical gear reducer shown in Figure P12-35 transmits 5.0 hp. Shaft 1 is the input, rotating at 1800 rpm and receiving power directly from an electric motor through a flexible coupling. Shaft 2 rotates at 900 rpm. Shaft 3 is the output, rotating at 300 rpm. A chain sprocket is mounted on the output shaft as shown and delivers the power upward. The data for the gears are given in Table 12-5. Each gear has a 1412° normal pressure angle and a 45° helix angle. The combinations of left- and right-hand helixes are arranged so that the axial forces oppose each other on shaft 2 as shown. Use SAE 4140 OQT 1200 for the shafts. Figure P12-35: P35-Double-reduction helical drive Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of…

Chapter 11 Solutions

Fundamentals of Engineering Thermodynamics

Ch. 11.9 - Prob. 1E Ch. 11.9 - Prob. 2E Ch. 11.9 - 3. What is an advantage of using the Redlich–Kwong...Ch. 11.9 - To determine the specific volume of superheated...Ch. 11.9 - Prob. 5E Ch. 11.9 - Prob. 6E Ch. 11.9 - Prob. 7E Ch. 11.9 - Prob. 8E Ch. 11.9 - Prob. 9E Ch. 11.9 - Prob. 10E

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The expression for the change in specific enthalpy. The expression for the change in internal energy. The expression for the change in the entropy