(a) Explanation Given information: At time ( t ) is zero the velocity ( v ) is zero. At time ( t ) is 0.4 sec the position ( x ) is 0.8 ft . Calculation: Show the a-t curve of an accelerometer record for the motion with areas as in Figure (1): Calculate the area ( A 1 ) using the relation: A 1 = 2 3 a ( 16 − 24 ) t 1 Here, a ( 16 − 24 ) is acceleration between 24 ft/s 2 to 16 ft/s 2 and t 1 is time between 0 to 0.2 sec. Substitute 8 ft/s 2 for a ( 16 − 24 ) and 0.2 sec for t 1 . A 1 = 2 3 × 8 × 0.2 = 1.0667 ft/s Calculate the area ( A 2 ) using the relation: A 2 = a ( 0 − 16 ) t 1 Here, a ( 0 − 16 ) is acceleration between 0 ft/s 2 to 16 ft/s 2 . Substitute 16 ft/s 2 for a ( 0 − 16 ) and 0.2 sec for t 1 . A 2 = 16 × 0.2 = 3.2 ft/s Calculate the area ( A 3 ) using the relation: A 3 = ( a ( 0 − 16 ) + a ( 0 − 8 ) 2 ) t 2 Here, a ( 0 − 8 ) is acceleration between 0 ft/s 2 to 8 ft/s 2 and t 2 is time between 0.2 sec to 0.3 sec. Substitute 16 ft/s 2 for a ( 0 − 16 ) , 8 ft/s 2 for a ( 0 − 8 ) and 0 (b) To determine The position of the part at time 0.3 sec ( x 0.3 ) and time 0.2 sec ( x 0.2 ) .

12th Edition

ISBN: 9781264095032

Author: BEER

Publisher: MCGRAW-HILL HIGHER EDUCATION

See similar textbooks

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be create…

Videos

Question

Chapter 11.3, Problem 11.77P

(a)

To determine

Construct the v-t curve for 0≤t≤0.4sec.

(b)

To determine

The position of the part at time 0.3 sec (x0.3) and time 0.2 sec (x0.2).

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11.3, Problem 11.76P

Chapter 11.3, Problem 11.78P

Students have asked these similar questions

Hints: Find the closed loop transfer function and then plot the step response for diFerentvalues of K in MATLAB. Show step response plot for different values of K. Auto Controls Show solutions and provide matlab code NO COPIED ANSWERS OR WILL REPORT!!!!

37. The vertical shaft shown in Figure P12-37 is driven at a speed of 600 rpm with 4.0 hp entering through the bevel gear. Each of the two chain sprockets delivers 2.0 hp to the side to drive mixer blades in a chemical reactor vessel. The bevel gear has a diametral pitch of 5, a pitch diameter of 9.000 in, a face width of 1.31 in, and a pressure angle of 20°. Use SAE 4140 OQT 1000 steel for the shaft. See Chapter 10 for the methods for computing the forces on the bevel gear. Figure P12-37: P37-Bevel gear drive with two chain sprockets Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of strength. Homework Problems 12-24, 12-35, and 12-37 from textbook, done in spreadsheet form. Place drawings of the load, shear, and bending moment body diagrams…

35. The double-reduction, helical gear reducer shown in Figure P12-35 transmits 5.0 hp. Shaft 1 is the input, rotating at 1800 rpm and receiving power directly from an electric motor through a flexible coupling. Shaft 2 rotates at 900 rpm. Shaft 3 is the output, rotating at 300 rpm. A chain sprocket is mounted on the output shaft as shown and delivers the power upward. The data for the gears are given in Table 12-5. Each gear has a 1412° normal pressure angle and a 45° helix angle. The combinations of left- and right-hand helixes are arranged so that the axial forces oppose each other on shaft 2 as shown. Use SAE 4140 OQT 1200 for the shafts. Figure P12-35: P35-Double-reduction helical drive Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of…

Chapter 11 Solutions

VECTOR MECHANIC

Ch. 11.1 - A bus travels the 100 miles between A and B at 50...Ch. 11.1 - Two cars A and B race each other down a straight...Ch. 11.1 - A snowboarder starts from rest at the top of a...Ch. 11.1 - The motion of a particle is defined by the...Ch. 11.1 - The vertical motion of mass A is defined by the...Ch. 11.1 - A loaded railroad car is rolling at a constant...Ch. 11.1 - A group of hikers uses a GPS while doing a 40-mile...Ch. 11.1 - The motion of a particle is defined by the...Ch. 11.1 - A girl operates a radio-controlled model car in a...Ch. 11.1 - The motion of a particle is defined by the...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Construct the v-t curve for 0 ≤ t ≤ 0.4 sec .

Solution Summary: The author shows the a-t curve of an accelerometer record for the motion with areas as in Figure 1.