Consider the system shown in Fig. 1–77. If a change of 0.7 kPa in the pressure of air causes the brine–mercury interface in the right column to drop by 5 mm in the brine level in the right column while the pressure in the brine pipe remains constant, determine the ratio of A2/A1.
The ratio of
Answer to Problem 81P
The ratio of
Explanation of Solution
Write the expression of pressure in U-tube manometer with before the pressure change of air.
Here, the pressure in area 1 is
Write the expression of pressure in U-tube manometer with after the pressure change of air.
Here, the pressure in area 2 is
Simplify the Equation (I) and Equation (II).
Here, the specific gravity of mercury is
Determine the change in specific enthalpy of mercury.
Here, the area 1 is
Substitute Equation (IV) into Equation (III).
Conclusion:
Substitute
Thus, the ratio of
Want to see more full solutions like this?
Chapter 1 Solutions
EBK THERMODYNAMICS: AN ENGINEERING APPR
Additional Engineering Textbook Solutions
Fundamentals of Aerodynamics
Fluid Mechanics: Fundamentals and Applications
Mechanics of Materials, 7th Edition
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Engineering Mechanics: Dynamics (14th Edition)
Foundations of Materials Science and Engineering
- The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in Figure below. The tank is located on a mountain at an altitude of 1400 m where the atmospheric pressure is 85.6 kPa. Take the densities of water, oil, and mercury to be 1000 kg/m3, 850 kg/m3 and 13600 kg/m3 respectively. Determine the air pressure in the tank. take data in figure 2.arrow_forwardDetermine the volume of 3 kg of saturated water with a quality of 60% and a pressure of 150 kPa.arrow_forwardDo it fastarrow_forward
- 7. An air bubble rises from the bottom of the well where the temperature is 20°C to the surface where the temperature is 50°C. If the existing atmospheric pressure at the surface of the well water is 101.3kPa, determine the percent increase in volume of the bubble if the pressure in the bottom of the well is 200kPag. Draw a figure or FBD that will support the problem. Explain each step by step formula.arrow_forwardConsider the system If a change Question 8 of 0.7 kPa in the pressure of air causes the brine-mercury interface in the right column to drop by 5 mm in the brine level in the right column while the pressure in the brine pipe remains constant, determine the ratio of A,/A1. Air Brine pipe SG = 1.1 Water Area, Aj. Area, A, Mercury SG = 13.56arrow_forwardDetermine properties of saturated vapor if its temperature is 228 °C.arrow_forward
- determine the pressure of superheated steam at 250 °c and specific volume of 0.05970 m3 /kg.arrow_forwardThe total pressure in a gas pipeline is to be maintained at three times atmospheric pressure. Figure 3 shows the cross-sectional area of the pipeline that is connected to a manometer filled with mercury. An inspector measures a difference of 1.25 m between the two columns of mercury. Is the gas pressure being maintained at the desired value? The density of mercury is 13600 kg/m3.arrow_forwardThe pressure at the bottom of a water tank is measured to be 150kPa. Calculate the height of the fluid (in ft) in the tank when it is exposed to an atmospheric pressure of 750mmHg.arrow_forward
- A rigid tank contains water at a pressure of 200 kPa. The volume of the tank is 2 m^3. The mass of liquid in the tank is 0.5643 kg and the mass of vapor in the tank is 2.2572 kg. In the question that follows, select the answer that is closest to the true value. What is the quality of the water in the tank?arrow_forwardThe inclined-tube manometer shown in Fig. 2-23 is used to measure small pressure changes. Determine the difference in pressure between points A and E if the manometer liquid, mercury, is at the level shown. The pipe at A contains water, and the one at E contains natural gas. For mercury, PHg 13 550 kg/m³. 400 mm B 100 mm 120° 700 mm Fig. 2-23 2arrow_forwardThe volume of a rock is to be determined without using any volume measurement device. Explain how you would do this with a waterproof spring scale.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY