Alpha, beta and gamma emissions have different penetrating power due to their characteristics. Concept Introduction : Gamma rays have a higher penetrating power than beta particles. Beta particles have a higher penetrating power than alpha particles. Correct answer: a. barium-140, bismuth-210, radium-223 Reason for correct answer: Gamma rays have a higher penetrating power than beca particles. Beta particles have a higher penetrating power than alpha particles. Since barium-140 is gamma emitter then this has the highest penetrating power. Bismuth-210 is beta emitter so this has a lower penetrating power than barium-140 but higher than Radium-223. Radium-223 has the lowest penetrating power since this is an alpha emitter. Reason for incorrect answer: Option bis incorrect because it considers that barium-140 has the least penetrating power. Option c is incorrect because it considers that radium-223 has the most penetrating power. Option d is incorrect because it considers that bismuth-210 has the least penetrating power. Conclusion: Thus, option (a) is correct option.

Question

Want to see the full answer?

Answer 1

Question

Chapter 11, Problem 47P

Interpretation Introduction

Interpretation:Alpha, beta and gamma emissions have different penetrating power due to their characteristics.

Concept Introduction:

Gamma rays have a higher penetrating power than beta particles.
Beta particles have a higher penetrating power than alpha particles.

Correct answer:

a. barium-140, bismuth-210, radium-223

Reason for correct answer:

Gamma rays have a higher penetrating power than beca particles.
Beta particles have a higher penetrating power than alpha particles.
Since barium-140 is gamma emitter then this has the highest penetrating power.
Bismuth-210 is beta emitter so this has a lower penetrating power than barium-140 but higher than Radium-223.
Radium-223 has the lowest penetrating power since this is an alpha emitter.

Reason for incorrect answer:

Option bis incorrect because it considers that barium-140 has the least penetrating power.
Option c is incorrect because it considers that radium-223 has the most penetrating power.
Option d is incorrect because it considers that bismuth-210 has the least penetrating power.

Conclusion: Thus, option (a) is correct option.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

eks.com/aleksogi/x/sl.exe/1o_u-IgNslkr7j8P3jH-IQs_pBanHhvTCeeBZbufuBYTI0Hz7m7D3ZS17Hd6m-HIl6n52njJN-TXdQA2X9yID-1SWQJTgnjARg30 111 States of Matter Understanding conceptual components of the enthalpy of solution 0/5 Ge A small amount of acetonitrile (CH, CN) is dissolved in a large amount of water. Imagine separating this process into the four stages sketched below. (These sketches show only a portion of the substances, so you can see the density and distribution of atoms and molecules in them.) CH,CN H₂O B 88 C Use these sketches to answer the questions in the table below. The enthalpy of solution AH is negative soln when CH3CN dissolves in water. Use this information to list the stages in order of increasing enthalpy. Would heat be absorbed or released if the system moved from Stage C to D? What force would oppose or favor the system moving from Stage C to D? Check all that apply. 1 absorbed O released neither absorbed nor released. none O ionic bonding force covalent bonding force…

In a system with an anodic overpotential, the variation of ŋ as a function of the current density: 1. at low fields is linear 2. at higher fields, it follows Tafel's law Find the range of current densities for which the overpotential has the same value as when calculated for cases 1 and 2 (maximum relative difference of 5% with respect to the behavior for higher fields). To which overpotential range does this correspond? Data: 10 = 1.5 mA cm², T = 300°C, ẞ = 0.64, R = 8.314 J K 1 mol‍¹ and F = 96485 C mol-1.

Indicate 10.6 with only one significant figure.