Construction Materials, Methods and Techniques (MindTap Course List)
4th Edition
ISBN: 9781305086272
Author: William P. Spence, Eva Kultermann
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 11, Problem 2RQ
To determine
The difference between surface clay and fireclay
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Consider the conditions in Practice Problem 5.2. How short would the driver reaction times of oncoming vehicles have to be for the probability of an accident to equal 0.20?
Part 4: Problem-Solving. Solve the following problems. Show all calculations.
1. A Standard Penetration Test (SPT) was conducted at a site, and the following blow counts were
recorded:
Depth: 2 m, Blow count (N): 10
D
D
Depth: 4 m, Blow count (N): 15
Depth: 6 m, Blow count (N): 20
The energy ratio is 60%, and the overburden correction factor CN is 1.1. Calculate the
corrected N-values for each depth.
2. A soil sample was collected from a depth of 3 m using a Shelby tube. The sample had a volume
of 0.01 m³ and a mass of 18 kg. If the water content is 12%, calculate the (a) bulk density, (b) dry
density, and (c) void ratio of the soil. Assume the specific gravity of soil solids (Gs) is 2.65.
3. A Cone Penetration Test (CPT) was conducted at a site, and the following data was obtained:
Depth: 2 m, Cone resistance (qc): 5 MPa
Depth: 4 m, Cone resistance (qc): 8 MPa
Depth: 6 m, Cone resistance (qc): 12 MPa
Estimate the soil type at each depth using typical qc correlations.
Pls show step by step and formula used
Chapter 11 Solutions
Construction Materials, Methods and Techniques (MindTap Course List)
Knowledge Booster
Similar questions
- A: Wel Question 2 (a) A simple circular hollow section (CHS) tubular K-joint in a steel structure, subjected to balanced axial loading, is illustrated in Figure 2a. Determine the maximum hot spot stress at the joint intersection of the chord and the loaded brace B. (b) The steel structure is installed in the seawater with cathodic protection. Determine the number of stress cycles to failure based on the maximum hot stress range obtained in part (a). Use the NORSOK standard. (Refer to S-N curves for tubular joints in air environment and seawater with cathodic protection). (c) Estimate the number of load repetitions required to induce fatigue failure in the tubular joint, based on the load history provided in Figure 2b. The nominal yield and ultimate tensile strength are 355 N/mm² and 510 N/mm², respectively. Assume a damage limit of 1.0. Use the Modified Goodman formulation to determine the equivalent completely reversed stress. (d) Describe briefly the procedure to determine the hot…arrow_forwardThe steel member is a fillet welded built-up section that comprises two flange plates (100mm x 20mm) and a web plate (250mm x 10mm) as depicted in Section A-A. The leg size of the weld is 8 mm. Use an appropriate consequence class. Based on the damage tolerant method and the modified Goodman equation. Determine an equivalent completely reversed stress. Ignore the vibration and dynamic amplification. Use Euro-code 1993-1-9. (a) Calculate the maximum and minimum stresses at steel member section A-A. (b) Check the fatigue resistance of the steel member at Section A-A using the fatigue limit. (c) Discuss the possible failure mode of the steel member due to fatigue loading. State your design assumptions, if any. Steel plate (Flange) 100mm x 20mm 10.0 m Fillet weld (manual) (Typical) Steel plate (Web) 250mm x 10 mm Steel plate (Flange) 100mm x 20mm Section A-A Fixed end Welded built-up steel section 5.0 m A 2.5m 3.0 m Fatigue load range 5 kN A Total weight of steel section Total weight of…arrow_forward30 20 10 Stress N/mm² 0 -10 -20 -30 Time Question 1 A Grade S355 steel member, which forms part of the structural framework supporting a storage tank in a warehouse, is subjected to various loads, as shown in Figure 1. The yield and tensile strength of the steel member are 355 N/mm² and 510 N/mm², respectively. The steel member is subjected to axial tension due to its self-weight and appurtenances of 40.0kN. The 10.0kN storage tank is positioned 1.0 m from the centreline of the steel member, and it experiences a fatigue load range of 5.0kN. The steel member is a fillet welded built-up section that comprises two flange plates (100mm x 20mm) and a web plate (250mm x 10mm) as depicted in Section A-A. The leg size of the weld is 8 mm. Use an appropriate consequence class. Based on the damage tolerant method and the modified Goodman equation. Determine an equivalent completely reversed stress. Ignore the vibration and dynamic amplification. Use Euro-code 1993-1-9. (a) Calculate the maximum…arrow_forward
- Please do not use design aid - R. Show step by step and every formular usedarrow_forwardFollowing is the variation of the field standard penetration number (№60) in a sand deposit: Depth (m) N60 1.5 6 3 8 4.5 9 6 8 7.5 9 13 14 The groundwater table is located at a depth of 6 m. Given: the dry unit weight of sand from 0 to a depth of 6 m is 16 kN/m³, and the saturated unit weight of sand for depth 6 to 12 m is 18.2 kN/m². Use the relationship given in the equation CN = 1 σo/Pa 0.5 to calculate the corrected penetration numbers. (Round your answers to the nearest whole number.) Depth (m) Neo (N1)00 1.5 3 6 8 4.5 9 6 7.5 9 14 8 13arrow_forward1,5 m 1,5 m A 1,6 KN F 0,8 m E 0,8 marrow_forward
- 5.85 The flow pattern through the pipe contraction is as shown, and the Q of water is 60 cfs. For d = 2 ft and D = 6 ft, what is the pressure at point B if the pressure at point C is 3200 psf? D E Problem 5.85 20° Barrow_forwardPlease solve problem 8.13 (the highlighted question).arrow_forwardThe following figure shows a vertical retaining wall with a granular backfill: 100.0 50.0 40.0 30.0 20.0 10.0- 5.0- 4.0 3.0- 2.0- = +1 0.8 0.6 0.4 0.2 0.0 -0.2 -0.4 -0.6 -0.8 -0.9 1.0- 0 10 20 30 40 45 ' (deg) (a) Figure Caquot and Kerisel's solution for K 3 Let H = 4m, a = 17.5°, y = 17.5 kN/m³, ' = 35°, and 8' = 10°. For given values of ' and 8', R' = 0.53. Based on Caquot and Kerisel's solution, what would be the passive force per meter length of the wall? (Enter your answer to two significant figures.) Pp= kN/marrow_forward
- The dam presented below is 180 m long (in the direction perpendicular to the plane of thecross-section). For the water elevations given on the drawing:a) Construct the flow net (minimum number of equipotential lines should be 10),b) Calculate the rate of seepage for the entire dam,c) Find the total uplift force on the dam (ignore barriers), andd) Estimate the hydraulic gradient at points A, B, and Darrow_forwardThe influence line for moment at B for the beam shown is A -6 m- B a. O at A, 6 at B, and 15 at C b. 1 at A, 1 at B, and 1 at C c. O at A, 0 at B, and -9 at C d. O at A, 1 at B, and 1 and C -9 m-arrow_forwardConsider the following figure: H/3 Pa Given: H = 7 m, y = 13 kN/m³, ø′ = 25°, c′ = 12 kN/m², and a = 10°. For given values, K₁ = 0.296. Calculate the Rankine active force per unit length of the wall after the occurrence of the tensile crack. (Enter your answer to three significant figures.) Pa = kN/marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781305081550Author:Braja M. DasPublisher:Cengage Learning
Construction Materials, Methods and Techniques (M...
Civil Engineering
ISBN:9781305086272
Author:William P. Spence, Eva Kultermann
Publisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781305081550
Author:Braja M. Das
Publisher:Cengage Learning