10th Edition

ISBN: 9781292178202

Author: HIBBELER

Publisher: PEARSON

See similar textbooks

Videos

Textbook Question

Chapter 11, Problem 11.6RP

The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is τ_allow = 350 psi and the allowable bending stress is σ_allow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stress concentration at the notch.

Chapter 11, Problem 11.6RP, The simply supported joist is used in the construction of a floor for a building. In order to keep

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11, Problem 11.5RP

Chapter 11, Problem 11.7RP

Students have asked these similar questions

Access Pearson Course Home Scores

Access Pearson Mastering Engineering Back to my courses Course Home Course Home Scores

Access Pearson Mastering Engineering Back to my courses Course Home Course Home Scores ■Review Next >

Chapter 11 Solutions

MECHANICS OF MATERIAL IN SI UNITS

Ch. 11.2 - Determine the minimum dimension a to the nearest...Ch. 11.2 - of the rod to safely support the load. The rod is...Ch. 11.2 - The wood has an allowable normal stress of allow =...Ch. 11.2 - of the beam's cross section to safely support the...Ch. 11.2 - Determine the minimum dimension b to the nearest...Ch. 11.2 - The beam is made of steel having an allowable...Ch. 11.2 - Determine its dimensions if it is to be...Ch. 11.2 - Determine the minimum width of the beam to the...Ch. 11.2 - if P=10 kip.Ch. 11.2 - If the allowable bending stress is allow = 22 ksi...

Ch. 11.2 - The allowable bending stress is allow = 24 ksi and...Ch. 11.2 - The allowable bending stress is allow = 22 ksi and...Ch. 11.2 - The allowable bending stress is allow = 24 ksi and...Ch. 11.2 - Select the lightest-weight wide-flange beam from...Ch. 11.2 - The beam has an allowable normal stress of allow =...Ch. 11.2 - The beam has an allowable normal stress of allow...Ch. 11.2 - If each nail can support a shear force of 200 lb....Ch. 11.2 - If each beam is to be designed to carry 90 lb/ft...Ch. 11.2 - Determine its height h so that it simultaneously...Ch. 11.2 - The beam is constructed from four boards. If each...Ch. 11.2 - Prob. 11.15P Ch. 11.2 - The beam has an allowable normal stress of allow....Ch. 11.2 - Determine the maximum cable force P that can...Ch. 11.2 - to safely support the load. The wood has an...Ch. 11.2 - and the wood has an allowable normal stress of...Ch. 11.2 - If the glue can support a shear stress of allow, =...Ch. 11.2 - If the allowable bending stress is allow = 6 MPa,...Ch. 11.2 - Determine the width b if the height h=2b.Ch. 11.2 - The allowable bending stress is allow = 24 ksi and...Ch. 11.2 - if allow = 30 ksi and allow = 15 ksi. The journal...Ch. 11.2 - if allow = 30 ksi and allow = 15 ksi. The journal...Ch. 11.2 - Select the lightest-weight wide-flange beam from...Ch. 11.2 - The allowable bending stress is allow = 30 ksi and...Ch. 11.2 - The allowable bending stress is allow = 30 ksi and...Ch. 11.2 - If the maximum bending stress is not to exceed...Ch. 11.2 - Determine the maximum load that can safely be...Ch. 11.4 - Determine the variation in the width was a...Ch. 11.4 - The tapered beam supports a uniform distributed...Ch. 11.4 - The tapered beam supports the concentrated force P...Ch. 11.4 - The beam is made from a plate that has a constant...Ch. 11.4 - Determine the variation in the depth d of a...Ch. 11.4 - Determine the variation of the radius r of the...Ch. 11.4 - Prob. 11.37P Ch. 11.4 - Determine the variation in the width b as a...Ch. 11.4 - The tubular shaft has an inner diameter of 15 mm....Ch. 11.4 - Prob. 11.40P Ch. 11.4 - Prob. 11.41P Ch. 11.4 - The pulleys fixed to the shaft are loaded as...Ch. 11.4 - Prob. 11.43P Ch. 11.4 - Prob. 11.44P Ch. 11.4 - Prob. 11.45P Ch. 11 - The cantilevered beam has a circular cross...Ch. 11 - Select the lightest-weight wide-flange overhanging...Ch. 11 - Prob. 11.3RP Ch. 11 - Determine the shaft's diameter to the nearest...Ch. 11 - Select the lightest-weight wide-flange beam from...Ch. 11 - The simply supported joist is used in the...Ch. 11 - The simply supported joist is used in the...Ch. 11 - by 4-in. pieces of wood braced as shown. If the...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts

Comprehension Check 7-14 The power absorbed by a resistor can be given by P = I2R, where P is power in units of...

Thinking Like an Engineer: An Active Learning Approach (4th Edition)

What types of coolant are used in vehicles?

Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)

Assume a telephone signal travels through a cable at two-thirds the speed of light. How long does it take the s...

Electric Circuits. (11th Edition)

The ____________ is always transparent.

Web Development and Design Foundations with HTML5 (8th Edition)

CONCEPT QUESTIONS 15.CQ3 The ball rolls without slipping on the fixed surface as shown. What is the direction ...

Vector Mechanics for Engineers: Statics and Dynamics

17–1C A high-speed aircraft is cruising in still air. How does the temperature of air at the nose of the aircra...

Thermodynamics: An Engineering Approach

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Solution Summary: The author calculates the height (h) that will cause the beam to reach both allowable stresses at the same time, and the load (p).

Videos

Want to see the full answer?

Chapter 11 Solutions

Additional Engineering Textbook Solutions