(a)
The mass flow rate of air in the gas-turbine cycle.
(a)
Answer to Problem 109RP
The mass flow rate of air in the gas-turbine cycle is
Explanation of Solution
Show the T-s diagram as in Figure (1).
Express Prandtl number at state 8s.
Here, pressure at state 8s is
Express enthalpy at state 8.
Here, enthalpy at state 7 is
Express Prandtl number at state 10s.
Here, pressure at state 10s is
Express enthalpy at state 10.
Here, enthalpy at state 9 is
Express enthalpy at state 1.
Here, enthalpy of saturation liquid at pressure of
Express specific volume at state 1.
Here, specific volume of saturation liquid at pressure of
Express initial work input.
Here, pressure at state 2 and 1 is
Express enthalpy at state 2.
Express quality at state 4s.
Here, entropy at state 4s is
Express enthalpy at state 4s.
Here, enthalpy at saturation liquid and evaporation at pressure of
Express enthalpy at state 4.
Here, enthalpy at state 3 is
Express quality at state 6s.
Here, entropy at state 6s is
Express enthalpy at state 6s.
Here, enthalpy at saturation liquid and evaporation at pressure of
Express enthalpy at state 6.
Here, enthalpy at state 5 is
Express the mass flow rate of air in the gas-turbine cycle from energy balance equation.
Here, enthalpy at state 10 is
Conclusion:
Refer Table A-17, “ideal gas properties of air”, and write the enthalpy at state 7 and Prandtl number at state 7 corresponding to temperature at state 7 of
Substitute
Refer Table A-17, “ideal gas properties of air”, and write the enthalpy at state 8s corresponding to Prandtl number at state 8s of
Write the formula of interpolation method of two variables.
Here, the variables denote by x and y is Prandtl number at state8s and enthalpy at state 8s respectively.
Show the enthalpy at state 8s corresponding to Prandtl number as in Table (1).
Prandtl number at state 8s |
Enthalpy at state 8s |
9.684 | 523.63 |
9.849 | |
10.37 | 533.98 |
Substitute
Thus, enthalpy at state 8s corresponding to Prandtl number at state 8s of
Substitute
Refer Table A-17, “ideal gas properties of air”, and write the enthalpy at state 9 and Prandtl number at state 9 corresponding to temperature at state 9 of
Here, enthalpy at state 9 is
Substitute
Refer Table A-17, “ideal gas properties of air”, and write the enthalpy at state 10s corresponding to Prandtl number at state 10s of
Show the enthalpy at state 10s corresponding to Prandtl number as in Table (2).
Prandtl number at state 10s |
Enthalpy at state 10s |
52.59 | 843.98 |
56.3 | |
57.60 | 866.08 |
Use excels and substitutes the values from Table (II) in Equation (XVI) to get,
Here, enthalpy at state 10s is
Substitute
Refer Table A-17, “ideal gas properties of air”, and write the enthalpy at state 11 corresponding to temperature at state 11 of
Here, enthalpy at state 11 is
Refer Table A-5, “saturated water-pressure table”, and write the properties at pressure of
Substitute
Substitute
Substitute
Substitute
Refer Table A-6, “superheated water”, and write the properties corresponding to pressure at state 3 of
Here, enthalpy and entropy at state 3 is
Due to throttling process, entropy at state 3 is equal to entropy at state 4s.
Refer Table A-5, “saturated water-pressure table”, and write the properties corresponding to pressure of
Substitute
Substitute
Substitute
Refer Table A-6, “superheated water”, and write the properties corresponding to pressure at state 5 of
Here, enthalpy and entropy at state 5 is
Due to throttling process, entropy at state 5 is equal to entropy at state 6s.
Refer Table A-5, “saturated water-pressure table”, and write the properties corresponding to pressure of
Substitute
Substitute
Substitute
Substitute
Hence, the mass flow rate of air in the gas-turbine cycle is
(b)
The rate of total heat input.
(b)
Answer to Problem 109RP
The rate of total heat input is
Explanation of Solution
Express the rate of total heat input.
Conclusion:
Substitute
Hence, the rate of total heat input is
(c)
The thermal efficiency of the combined cycle.
(c)
Answer to Problem 109RP
The thermal efficiency of the combined cycle is
Explanation of Solution
Express the rate of total heat output.
Express the thermal efficiency of the combined cycle.
Conclusion:
Substitute
Substitute
Hence, the thermal efficiency of the combined cycle is
Want to see more full solutions like this?
Chapter 10 Solutions
THERMODYNAMICS-SI ED. EBOOK >I<
- 20. [Ans. 9; 71.8 mm] A semi-elliptical laminated spring is made of 50 mm wide and 3 mm thick plates. The length between the supports is 650 mm and the width of the band is 60 mm. The spring has two full length leaves and five graduated leaves. If the spring carries a central load of 1600 N, find: 1. Maximum stress in full length and graduated leaves for an initial condition of no stress in the leaves. 2. The maximum stress if the initial stress is provided to cause equal stress when loaded. [Ans. 590 MPa ; 390 MPa ; 450 MPa ; 54 mm] 3. The deflection in parts (1) and (2).arrow_forwardQ6/ A helical square section spring is set inside another, the outer spring having a free length of 35 mm greater than the inner spring. The dimensions of each spring are as follows: Mean diameter (mm) Side of square section (mm) Active turns Outer Inner Spring Spring 120 70 8 7 20 15 Determine the (1) Maximum deflection of the two springs and (2) Equivalent spring rate of the two springs after sufficient load has been applied to deflect the outer spring 60 mm. Use G = 83 GN/m².arrow_forwardQ2/ The bumper springs of a railway carriage are to be made of rectangular section wire. The ratio of the longer side of the wire to its shorter side is 1.5, and the ratio of mean diameter of spring to the longer side of wire is nearly equal to 6. Three such springs are required to bring to rest a carriage weighing 25 kN moving with a velocity of 75 m/min with a maximum deflection of 200 mm. Determine the sides of the rectangular section of the wire and the mean diameter of coils when the shorter side is parallel to the axis of the spring. The allowable shear stress is not to exceed 300 MPa and G = 84 kN/mm². Q6/ A belicalarrow_forward
- 11. A load of 2 kN is dropped axially on a close coiled helical spring, from a height of 250 mm. The spring has 20 effective turns, and it is made of 25 mm diameter wire. The spring index is 8. Find the maximum shear stress induced in the spring and the amount of compression produced. The modulus of rigidity for the material of the spring wire is 84 kN/mm². [Ans. 287 MPa; 290 mm]arrow_forwardWhat is the reason for this composition?arrow_forwardHomework: ANOVA Table for followed design B AB Dr -1 -1 1 (15.18,12) 1 -1 -1 (45.48.51) -1 1 -1 (25,28,19) 1 1 (75.75,81)arrow_forward
- S B Pin 6 mm Garrow_forwardMid-Term Exam 2024/2025 Post graduate/Applied Mechanics- Metallurgy Q1/ State the type of fault in the following case, and state the structure in which it will appear. АВСАВСВАСВАСАВСАВСarrow_forwardالثانية Babakt Momentum equation for Boundary Layer S SS -Txfriction dray Momentum equation for Boundary Layer What laws are important for resolving issues 2 How to draw. 3 What's Point about this.arrow_forward
- R αι g The system given on the left, consists of three pulleys and the depicted vertical ropes. Given: ri J₁, m1 R = 2r; απ r2, J2, m₂ m1; m2; M3 J1 J2 J3 J3, m3 a) Determine the radii 2 and 3.arrow_forwardB: Solid rotating shaft used in the boat with high speed shown in Figure. The amount of power transmitted at the greatest torque is 224 kW with 130 r.p.m. Used DE-Goodman theory to determine the shaft diameter. Take the shaft material is annealed AISI 1030, the endurance limit of 18.86 kpsi and a factor of safety 1. Which criterion is more conservative? Note: all dimensions in mm. 1 AA Motor 300 Thrust Bearing Sprocket 100 9750 เอarrow_forwardQ2: The plate material of a pressure vessel is AISI 1050 QT 205 °C. The plate is rolled to a diameter of 1.2 m. The two sides of the plate are connected via a riveted joint as shown below. If the rivet material is G10500 with HB=197 and all rivet sizes M31. Find the required rivet size when the pressure vessel is subjected to an internal pressure of 500 MPa. Take safety factor = 2. 1.2m A B' A Chope olm 10.5 0.23 hopearrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY