Explanation Given: The radius of the sphere is r . The constant density of the sphere is ρ . Explanation: Show the intersection of the sphere at the arbitrary point ( x , y ) as in Figure (1). Calculation: From Figure 1, Calculate the differential mass of the sphere. d m = ρ d V (I) Here, the density of the material is ρ and the volume of the sphere is V . Substitute π y 2 d x for d V in Equation (I). d m = ρ ( π y 2 d x ) (II) Compute the centroid of the differential element along the y - axis. x 2 + y 2 = r 2 y 2 = r 2 − x 2 Substitute r 2 − x 2 for y 2 in Equation (II). d m = ρ π ( r 2 − x 2 ) d x Compute the moment of inertia of the differential element parallel to the y -axis and about the x -axis. d I x = y 2 2 d m (III) Here, the differential mass is d m , and the centroid of the differential element along the y - axis is y 2 . Substitute ρ π ( r 2 − x 2 ) d x for d m and r 2 − x 2 for y 2 in Equation (III). d I x = ( r 2 − x 2 ) 2 ρ π ( r 2 − x 2 ) d x = 1 2 ρ π ( r 2 − x 2 ) 2 d x Conclusion: Express the moment of inertia of the paraboloid about the x -axis. I x = ∫ − r r d I x (IV) Substitute 1 2 ρ π ( r 2 − x 2 ) 2 d x for d I x in Equation (IV). I x = ∫ − r r [ 1 2 ρ π ( r 2 − x 2 ) 2 d x ] = 1 2 ρ π ∫ − r r ( r 4 + x 4 − 2 r 2 x 2 ) d x = 1 2 ρ π ∫ − r r r 4 d x − ∫ − r r 2 r 2 x 2 d x + ∫ − r r x <

INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)

14th Edition

ISBN: 9780133918922

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Concept explainers

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provi…

Videos

Question

Chapter 10.8, Problem 92P

To determine

The moment of inertia Ix of the sphere, in terms of the total mass m of the sphere.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 10.8, Problem 91P

Chapter 10.8, Problem 93P

Students have asked these similar questions

A boiler with 80% efficiency produces steam at 40bar and 500 C at a rate of 1.128kg/s. The temperature of the feed water is raised from 25 C to 125 C in the economizer and the ambient air is drawn to the boiler at a rate of 2.70 kg/s at 16 C. The flue gases leave the chimney at rate of 3 kg/s at 150 C with specific heat of 1.01 kJ/kg.K. The dryness fraction of steam collected in the steam drum is 0.95. 1- Determine the heat value of the fuel. 2- The equivalence evaporation. 3- Draw the heat balance sheet.

A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diameter hole drilled transversely through it. The shaft is subjected to a pulsating torque fluctuating from 20 to 160 Nm and a completely reversed bending moment of 200 Nm. The steel tubing has a minimum strength of Sut = 410 MPa (60 ksi). The static stress-concentration factor for the hole is 2.4 for bending and 1.9 for torsion. The maximum operating temperature is 400˚C and a reliability of 99.9% is to be assumed. Find the factor of safety for infinite life using the modified Goodman failure criterion.

I need help with a MATLAB code. This code just keeps running and does not give me any plots. I even reduced the tolerance from 1e-9 to 1e-6. Can you help me fix this? Please make sure your solution runs. % Initial Conditions rev = 0:0.001:2; g1 = deg2rad(1); g2 = deg2rad(3); g3 = deg2rad(6); g4 = deg2rad(30); g0 = deg2rad(0); Z0 = 0; w0 = [0; Z0*cos(g0); -Z0*sin(g0)]; Z1 = 5; w1 = [0; Z1*cos(g1); -Z1*sin(g1)]; Z2 = 11; w2 = [0; Z2*cos(g2); -Z2*sin(g2)]; [v3, psi3, eta3] = Nut_angle(Z2, g2, w2); plot(v3, psi3) function dwedt = K_DDE(~, w_en) % Extracting the initial condtions to a variable % Extracting the initial condtions to a variable w = w_en(1:3); e = w_en(4:7); Z = w_en(8); I = 0.060214; J = 0.015707; x = (J/I) - 1; y = Z - 1; s = Z; % Kinematic Differential Equations dedt = zeros(4,1); dedt(1) = pi*(e(3)*(s-w(2)-1) + e(2)*w(3) + e(4)*w(1)); dedt(2) = pi*(e(4)*(w(2)-1-s) + e(3)*w(1) - e(1)*w(3)); dedt(3) = pi*(-e(1)*(s-w(2)-1) - e(2)*w(1) + e(4)*w(3));…

Chapter 10 Solutions

INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The moment of inertia I x of the sphere, in terms of the total mass m of the sphere.

Solution Summary: The author calculates the moment of inertia of the differential element parallel to the y -axis.

Concept explainers

Videos

The moment of inertia Ix of the sphere, in terms of the total mass m of the sphere.

Want to see the full answer?

Chapter 10 Solutions