Explanation Given: The total height of the beam's cross-sectional area is 200 mm . The total width of the beam's cross-sectional area is 200 mm . Explanation: To determine the distance y ¯ and the moment of inertia I ¯ x ′ about the x ′ axis, subdivide the cross-sectional area into 3 segments as follows: Part 1: Rectangle Part 2: Rectangle Part 3: Rectangle Show the subdivided beam's cross-sectional area along with their respective centroids as in Figure 1: From Figure (1), Write the height and the width of the rectangle in part 1: b 1 = 17 0 mm h 1 = 3 0 mm Here, height of rectangle in part 1 is h 1 and width of rectangle in part 1 is b 1 . Write the height and width of the rectangle in part 2. b 2 = 3 0 mm h 2 = 17 0 mm Here, the height of the rectangle in part 2 is h 2 and the width of the rectangle in part 2 is b 2 . Write the height and width of the rectangle in part 3: b 3 = 10 0 mm h 3 = 3 0 mm Here, the height of rectangle in part 3 is h 3 and the width of rectangle in part 3 is b 3 : Centroid calculation: Calculate the distance between the centroid and y axis for rectangle in part 1: y ¯ 1 = h 1 2 (I) Substitute 30 mm for h 1 in Equation (I). y ¯ 1 = 30 2 = 15 mm Calculate the distance between centroid and y axis for the rectangle in part 2: y ¯ 2 = h 2 2 (II) Substitute 170 mm for h 2 in Equation (II). y ¯ 2 = 170 2 = 85 mm Calculate the distance between centroid and y axis for the rectangle in part 3: y ¯ 3 = h 2 + h 3 2 (III) Substitute 170 mm for h 2 , and 30 mm for h 3 in Equation (III). y ¯ 3 = 170 + 30 2 = 185 mm Conclusion: Calculate the distance y ¯ to the centroid C of the beam's cross-sectional area. y ¯ = A 1 y ¯ 1 + A 2 y ¯ 2 + A 3 y ¯ 3 A 1 + A 2 + A 3 = ( b 1 h 1 ) y ¯ 1 + ( b 2 h 2 ) y ¯ 2 + ( b 3 h 3 ) y ¯ 3 ( b 1 h 1 ) + ( b 2 h 2 ) + ( b 3 h 3 ) (IV) Substitute 170 mm for b 1 , 30 mm for h 1 , 30 mm for b 2 , 170 mm for h 2 , 100 mm for b 3 , 30 mm for h 3 , 15 mm for y ¯ 1 , 85 mm for y ¯ 2 , and 185 mm for y ¯ 3 in Equation (IV). y ¯ = ( 170 ) ( 30 ) ( 15 ) + ( 170 ) ( 30 ) ( 85 ) + ( 100 ) ( 30 ) ( 185 ) ( 170 ) ( 30 ) + ( 170 ) ( 30 ) + ( 100 ) ( 30 ) = 76 , 500 + 433 , 500 + 555 , 000 5 , 100 + 5 , 100 + 3 , 000 = 106 , 5000 13 , 200 = 80.68 mm ≈ 80.7 mm Hence, the distance y ¯ to the centroid C of the beam's cross-sectional area is 80 .7 mm _ . Moment of inertia calculation: Calculate the distance between centroid and x ′ axis about y axis for rectangle in part 1. d y 1 = y ¯ − h 1 / 2 (V) Substitute 80

INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)

14th Edition

ISBN: 9780133918922

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Concept explainers

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provi…

Videos

Question

Chapter 10.4, Problem 44P

To determine

The distance y¯ and the moment of inertia I¯x′ about the x′ axis.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 10.4, Problem 43P

Chapter 10.4, Problem 45P

Students have asked these similar questions

Calculate the Von-Mises effective stress at the selected element within the wall (Fig. Q3) if T = 26.7 KN.m, P = 23.6 MPa, t = 2.2 mm, R = 2 m. The following choices are provided in units of MPa and rounded to three decimal places Select one: O 1.27870.272 O2. 18580.181 3. 11148.109 O 4. 14864.145 O 5.22296.218

A bar of length L and of a circular cross-section of diameter D is clamped at the top end and loaded at the other (bottom) end by a point load P as shown in Figure Q2a. The cross-section of the bar is shown in Figure Q2b indicating that load is applied at the point A. The material used in the bar has specific weight y. Find the magnitude and location of the maximum normal stress in the bar. Figure Q2 a Figure Q2 b 45°

A close end tube of thin-walled circular section may be subjected to torque Tand internal pressure P, as shown in Figure Q3. The shear stress in the wall caused by the torque can be calculated as σ = T/(2πR²t), where the mean radius of the cross section is R(i.e., the radius of the centreline of the wall) and the wall thickness is t. The internal radius of the tube can be calculated as (R-t/2). However, as R>> t, you can approximately assume that the internal radius of the tube is equal to Rin the subsequent calculation. The tube is made from a material with Young's modulus E, Poisson's ratio v. Orr T Ozz бее буг Z бее T бел Figure Q3 Centreline of the wall R

Chapter 10 Solutions

INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The distance y ¯ and the moment of inertia I ¯ x ′ about the x ′ axis.

Solution Summary: The author explains how to determine the distance and moment of inertia of the beam's cross-sectional area.

Concept explainers

Videos

The distance y¯ and the moment of inertia I¯x′ about the x′ axis.

Want to see the full answer?

Chapter 10 Solutions